16 CFR 1500.133 - Extremely flammable contact adhesives; labeling.

§ 1500.133 Extremely flammable contact adhesives; labeling.
(a) Extremely flammable contact adhesives, also known as contact bonding cements, when distributed in containers intended or suitable for household use may be misbranded under the act if the containers fail to bear a warning statement adequate for the protection of the public health and safety.
(b) The following warning statement is considered as the minimum cautionary labeling adequate to meet the requirements ofsection 2(p)(1) of the act (repeated in § 1500.3(b)(14)(i)) with respect to containers of more than one-half pint of contact adhesive and similar liquid or semiliquid articles having a flashpoint at or below 20 °F. as determined by the method in § 1500.43, when the only hazard foreseeable is that caused by the extreme flammability of the mixture:
Danger
Extremely Flammable
Vapors May Cause Flash Fire
Vapors may ignite explosively.
Prevent buildup of vapors—open all windows and doors—use only with cross-ventilation.
Keep away from heat, sparks, and open flame.
Do not smoke, extinguish all flames and pilot lights, and turn off stoves, heaters, electric motors, and other sources of ignition during use and until all vapors are gone.
Close container after use.
Keep out of the reach of children.
(c) The words that are in capital letters in the warning statement set forth in paragraph (b) of this section should be printed on the main (front) panel or panels of the container in capital letters of the type size specified in§ 1500.121(c). The balance of the cautionary information may appear together on another panel provided the front panel bears a statement such as “Read carefully other cautions on ___ panel,” the blank being filled in with the identification of the specific label panel bearing the balance of the cautionary labeling. It is recommended that a borderline be used in conjunction with the cautionary labeling.
(d) If an article has additional hazards, or contains ingredients listed in§ 1500.14 as requiring special labeling, appropriate additional front and rear panel precautionary labeling is required.
(e) Since the Commission has issued a regulation banning under the Consumer Product Safety Act extremely flammable contact adhesives covered by this labeling regulation (sec.16 CFR part 1302), paragraphs (a), (b), (c) and (d) of this section are revoked as to the subject products after June 13, 1978.
[38 FR 27012, Sept. 27, 1973, as amended at 42 FR 63742, Dec. 19, 1977]
Beta! The text on the eCFR tab represents the unofficial eCFR text at ecfr.gov.
§ 1500.133 Extremely flammable contact adhesives; labeling.

(a) Extremely flammable contact adhesives, also known as contact bonding cements, when distributed in containers intended or suitable for household use may be misbranded under the act if the containers fail to bear a warning statement adequate for the protection of the public health and safety.

(b) The following warning statement is considered as the minimum cautionary labeling adequate to meet the requirements of section 2(p)(1) of the act (repeated in § 1500.3(b)(14)(i)) with respect to containers of more than one-half pint of contact adhesive and similar liquid or semiliquid articles having a flashpoint at or below 20 °F. as determined by the method in § 1500.43, when the only hazard foreseeable is that caused by the extreme flammability of the mixture:

Danger
Extremely Flammable
Vapors May Cause Flash Fire

Vapors may ignite explosively.

Prevent buildup of vapors - open all windows and doors - use only with cross-ventilation.

Keep away from heat, sparks, and open flame.

Do not smoke, extinguish all flames and pilot lights, and turn off stoves, heaters, electric motors, and other sources of ignition during use and until all vapors are gone.

Close container after use.

Keep out of the reach of children.

(c) The words that are in capital letters in the warning statement set forth in paragraph (b) of this section should be printed on the main (front) panel or panels of the container in capital letters of the type size specified in § 1500.121(c). The balance of the cautionary information may appear together on another panel provided the front panel bears a statement such as “Read carefully other cautions on ___ panel,” the blank being filled in with the identification of the specific label panel bearing the balance of the cautionary labeling. It is recommended that a borderline be used in conjunction with the cautionary labeling.

(d) If an article has additional hazards, or contains ingredients listed in § 1500.14 as requiring special labeling, appropriate additional front and rear panel precautionary labeling is required.

(e) Since the Commission has issued a regulation banning under the Consumer Product Safety Act extremely flammable contact adhesives covered by this labeling regulation (sec. 16 CFR part 1302), paragraphs (a), (b), (c) and (d) of this section are revoked as to the subject products after June 13, 1978.

[38 FR 27012, Sept. 27, 1973, as amended at 42 FR 63742, Dec. 19, 1977]

Title 16 published on 2015-01-01

The following are ALL rules, proposed rules, and notices (chronologically) published in the Federal Register relating to 16 CFR Part 1500 after this date.

  • 2015-11-19; vol. 80 # 223 - Thursday, November 19, 2015
    1. 80 FR 72342 - Amendment To Clarify When Component Part Testing Can Be Used and Which Textile Products Have Been Determined Not To Exceed the Allowable Lead Content Limits; Delay of Effective Date and Extension of Comment Period
      GPO FDSys XML | Text
      CONSUMER PRODUCT SAFETY COMMISSION
      Direct final rule; delay of effective date and extension of comment period.
      The effective date for the direct final rule published October 14, 2015, at 80 FR 61729, is delayed from December 14, 2015, until January 13, 2016. The rule will be effective unless we receive a significant adverse comment. If we receive a significant adverse comment, we will publish notification in the Federal Register withdrawing this direct final rule before its effective date. The comment date is extended to December 14, 2015.
      16 CFR Parts 1109 and 1500