40 CFR Part 63, Subpart MMMMM, Table 5 to Subpart MMMMM of Part 63 - Continuous Compliance With Emission Limits and Operating Limits

Status message

There are 19 Updates appearing in the Federal Register for 40 CFR Part 63. View below or at eCFR (GPOAccess)
View PDF at GPOPt. 63, Subpt. MMMMM, Table 5
Table 5 to Subpart MMMMM of Part 63—Continuous Compliance With Emission Limits and Operating Limits
As stated in § 63.8812(a), you must comply with the requirements to demonstrate continuous compliance with the applicable emission limits or operating limits in the following table:
For . . . For the following emission limits or operating limits . . . You must demonstrate continuous compliance by . . .
1. Each new, reconstructed, or existing loop slitter affected source Eliminate use of HAP-based adhesives Not using HAP-based adhesives.
2. Each new or reconstructed flame lamination affected source using a scrubber a. Maintain the daily average scrubber inlet liquid flow rate above the minimum value established during the performanceb. Maintain the daily average scrubber effluent pH within the operating range established during the performance testc. Maintain the daily average pressure drop across the venturi within the operating range established during the performance test. If you use another type of scrubber (e.g., packed bed or spray tower scrubber), monitoring pressure drop is not required i. Collecting the scrubber inlet liquid flow rate and effluent pH monitoring data according to § 63.8804(a) through (c).ii. Reducing the data to 1-hour and daily block averages according to the requirements in § 63.8804(a).iii. Maintaining each daily average scrubber inlet liquid flow rate above the minimum value established during the performance test.iv. Maintaining the daily average scrubber effluent pH within the operating range established during the performance test.v. If you use a venturi scrubber, maintaining the daily average pressure drop across the venturi within the operating range established during the performance test.
3. Each new or reconstructed flame lamination affected source using any other control device a. Maintain the daily average operating parameters above the minimum value established during the performance test, or within the range established during the performance test, as applicable i. Collected the operating parameter data according to the site-specific test plan.ii. Reducing the data to one-hour averages according to the requirements in § 63.8804(a).iii. Maintaining the daily average during the rate above the minimum value established during the performance test, or within the range established during the performance test, as applicable.

Title 40 published on 2014-07-01.

The following are only the Rules published in the Federal Register after the published date of Title 40.

For a complete list of all Rules, Proposed Rules, and Notices view the Rulemaking tab.

  • 2015-06-03; vol. 80 # 106 - Wednesday, June 3, 2015
    1. 80 FR 31470 - Completion of Requirement To Promulgate Emissions Standards
      GPO FDSys XML | Text
      ENVIRONMENTAL PROTECTION AGENCY
      Final rule.
      This action is effective on June 3, 2015.
      40 CFR Part 63

This is a list of United States Code sections, Statutes at Large, Public Laws, and Presidential Documents, which provide rulemaking authority for this CFR Part.

This list is taken from the Parallel Table of Authorities and Rules provided by GPO [Government Printing Office].

It is not guaranteed to be accurate or up-to-date, though we do refresh the database weekly. More limitations on accuracy are described at the GPO site.


United States Code

Title 40 published on 2014-07-01

The following are ALL rules, proposed rules, and notices (chronologically) published in the Federal Register relating to 40 CFR Part 63 after this date.

  • 2015-06-03; vol. 80 # 106 - Wednesday, June 3, 2015
    1. 80 FR 31470 - Completion of Requirement To Promulgate Emissions Standards
      GPO FDSys XML | Text
      ENVIRONMENTAL PROTECTION AGENCY
      Final rule.
      This action is effective on June 3, 2015.
      40 CFR Part 63