47 CFR 73.160 - Vertical plane radiation characteristics, f(θ).

§ 73.160 Vertical plane radiation characteristics, f(θ).
(a) The vertical plane radiation characteristics show the relative field being radiated at a given vertical angle, with respect to the horizontal plane. The vertical angle, represented as θ, is 0 degrees in the horizontal plane, and 90 degrees when perpendicular to the horizontal plane. The vertical plane radiation characteristic is referred to as f(θ). The generic formula for f(θ) is:
f(θ)=E(θ)/E(O)
where:
E(θ) is the radiation from the tower at angle θ.
E(O) is the radiation from the tower in the horizontal plane.
(b) Listed below are formulas for f(θ) for several common towers.
(1) For a typical tower, which is not top-loaded or sectionalized, the following formula shall be used:
where:
G is the electrical height of the tower, not including the base insulator and pier. (In the case of a folded unipole tower, the entire radiating structure's electrical height is used.)
(2) For a top-loaded tower, the following formula shall be used:
where:
A is the physical height of the tower, in electrical degrees, and
B is the difference, in electrical degrees, between the apparent electrical height (G, based on current distribution) and the actual physical height.
G is the apparent electrical height: the sum of A and B; A B.
See Figure 1 of this section.
(3) For a sectionalized tower, the following formula shall be used:
where:
A is the physical height, in electrical degrees, of the lower section of the tower.
B is the difference between the apparent electrical height (based on current distribution) of the lower section of the tower and the physical height of the lower section of the tower.
C is the physical height of the entire tower, in electrical degrees.
D is the difference between the apparent electrical height of the tower (based on current distribution of the upper section) and the physical height of the entire tower. D will be zero if the sectionalized tower is not top-loaded.
G is the sum of A and B; A B.
H is the sum of C and D; C D.
Δ is the difference between H and A; H−A.
See Figure 2 of this section.
(c) One of the above f(θ) formulas must be used in computing radiation in the vertical plane, unless the applicant submits a special formula for a particular type of antenna. If a special formula is submitted, it must be accompanied by a complete derivation and sample calculations. Submission of values for f(θ) only in a tabular or graphical format (i.e., without a formula) is not acceptable.
(d) Following are sample calculations. (The number of significant figures shown here should not be interpreted as a limitation on the number of significant figures used in actual calculations.)
(1) For a typical tower, as described in paragraph (b)(1) of this section, assume that G=120 electrical degrees:
θ f(θ)
0 1.0000
30 0.7698
60 0.3458
(2) For a top-loaded tower, as described in paragraph (b)(2) of this section, assume A=120 electrical degrees, B=20 electrical degrees, and G=140 electrical degrees, (120 20):
θ f(θ)
0 1.0000
30 0.7364
60 0.2960
(3) For a sectionalized tower, as described in paragraph (b)(3) of this section, assume A=120 electrical degrees, B=20 electrical degrees, C=220 electrical degrees, D=15 electrical degrees, G=140 electrical degrees (120 20), H=235 electrical degrees (220 15), and Δ=115 electrical degrees (235−120):
θ f(θ)
0 1.0000
30 0.5930
60 0.1423
[46 FR 11993, Feb. 12, 1981]
Beta! The text on the eCFR tab represents the unofficial eCFR text at ecfr.gov.
§ 73.160 Vertical plane radiation characteristics, f(θ).

(a) The vertical plane radiation characteristics show the relative field being radiated at a given vertical angle, with respect to the horizontal plane. The vertical angle, represented as θ, is 0 degrees in the horizontal plane, and 90 degrees when perpendicular to the horizontal plane. The vertical plane radiation characteristic is referred to as f(θ). The generic formula for f(θ) is:

f(θ) = E(θ)/E(O)
where:
E(θ) is the radiation from the tower at angle θ.
E(O) is the radiation from the tower in the horizontal plane.

(b) Listed below are formulas for f(θ) for several common towers.

(1) For a typical tower, which is not top-loaded or sectionalized, the following formula shall be used:

where:
G is the electrical height of the tower, not including the base insulator and pier. (In the case of a folded unipole tower, the entire radiating structure's electrical height is used.)

(2) For a top-loaded tower, the following formula shall be used:

where:
A is the physical height of the tower, in electrical degrees, and
B is the difference, in electrical degrees, between the apparent electrical height (G, based on current distribution) and the actual physical height.
G is the apparent electrical height: the sum of A and B; A B.

See Figure 1 of this section.

(3) For a sectionalized tower, the following formula shall be used:

where:
A is the physical height, in electrical degrees, of the lower section of the tower.
B is the difference between the apparent electrical height (based on current distribution) of the lower section of the tower and the physical height of the lower section of the tower.
C is the physical height of the entire tower, in electrical degrees.
D is the difference between the apparent electrical height of the tower (based on current distribution of the upper section) and the physical height of the entire tower. D will be zero if the sectionalized tower is not top-loaded.
G is the sum of A and B; A B.
H is the sum of C and D; C D.
Δ is the difference between H and A; H−A.

See Figure 2 of this section.

(c) One of the above f(θ) formulas must be used in computing radiation in the vertical plane, unless the applicant submits a special formula for a particular type of antenna. If a special formula is submitted, it must be accompanied by a complete derivation and sample calculations. Submission of values for f(θ) only in a tabular or graphical format (i.e., without a formula) is not acceptable.

(d) Following are sample calculations. (The number of significant figures shown here should not be interpreted as a limitation on the number of significant figures used in actual calculations.)

(1) For a typical tower, as described in paragraph (b)(1) of this section, assume that G = 120 electrical degrees:

θ f(θ)
0 1.0000
30 0.7698
60 0.3458

(2) For a top-loaded tower, as described in paragraph (b)(2) of this section, assume A = 120 electrical degrees, B = 20 electrical degrees, and G = 140 electrical degrees, (120 20):

θ f(θ)
0 1.0000
30 0.7364
60 0.2960

(3) For a sectionalized tower, as described in paragraph (b)(3) of this section, assume A = 120 electrical degrees, B = 20 electrical degrees, C = 220 electrical degrees, D = 15 electrical degrees, G = 140 electrical degrees (120 20), H = 235 electrical degrees (220 15), and Δ = 115 electrical degrees (235−120):

θ f(θ)
0 1.0000
30 0.5930
60 0.1423
[46 FR 11993, Feb. 12, 1981]

This is a list of United States Code sections, Statutes at Large, Public Laws, and Presidential Documents, which provide rulemaking authority for this CFR Part.

This list is taken from the Parallel Table of Authorities and Rules provided by GPO [Government Printing Office].

It is not guaranteed to be accurate or up-to-date, though we do refresh the database weekly. More limitations on accuracy are described at the GPO site.

United States Code

Title 47 published on 2015-10-01

The following are ALL rules, proposed rules, and notices (chronologically) published in the Federal Register relating to 47 CFR Part 73 after this date.

• 2015-12-02; vol. 80 # 231 - Wednesday, December 2, 2015
1. 80 FR 75431 - Expanding the Economic and Innovation Opportunities of Spectrum Through Incentive Auctions
GPO FDSys XML | Text
FEDERAL COMMUNICATIONS COMMISSION
Final rule; announcement of effective date.
47 CFR 1.2204(a), (c), (d)(3), and (d)(5) and 73.3700(h)(4) and (6) and FCC Form 177, Application to Participate in a Reverse Incentive Auction, published at 79 FR 48442, August 15, 2014, are effective on December 2, 2015.
47 CFR Parts 1 and 73