Repeat
(47) Repeat means an unintended or unexpected successive stroke of the press resulting from a malfunction. (48) Safety block means a prop that, when inserted between the upper and lower dies or between the bolster plate and the face of the slide, prevents the slide from falling of its own deadweight. (49) Single stroke means one complete stroke of the slide, usually initiated from a full open (or up) position, followed by closing (or down), and then a return to the full open position. (50) Single stroke mechanism means an arrangement used on a full revolution clutch to limit the travel of the slide to one complete stroke at each engagement of the clutch. (51) Slide means the main reciprocating press member. A slide is also called a ram, plunger, or platen. (52) Stop control means an operator control designed to immediately deactivate the clutch control and activate the brake to stop slide motion. (53) Stripper means a mechanism or die part for removing the parts or material from the punch. (54) Stroking selector means the part of the clutch/brake control that determines the type of stroking when the operating means is actuated. The stroking selector generally includes positions for Off (Clutch Control), Inch, Single Stroke, and Continuous (when Continuous is furnished). (55) Trip or (tripping) means activation of the clutch to run the press. (56) Turnover bar means a bar used in die setting to manually turn the crankshaft of the press. (57) Two-hand trip means a clutch actuating means requiring the concurrent use of both hands of the operator to trip the press. (58) Unitized tooling means a type of die in which the upper and lower members are incorporated into a selfcontained unit so arranged as to hold the die members in alignment. (59) Control system means sensors, manual input and mode selection elements, interlocking and decision-making circuitry, and output elements to the press operating mechanism. (60) Brake monitor means a sensor designed, constructed, and arranged to monitor the effectiveness of the press braking system. (61) Presence sensing device initiation means an operating mode of indirect manual initiation of a single stroke by a presence sensing device when it senses that work motions of the operator, related to feeding and/or removing parts, are completed and all parts of the operator's body or hand tools are safely clear of the point of operation. (62) Safety system means the integrated total system, including the pertinent elements of the press, the controls, the safeguarding and any required supplemental safeguarding, and their interfaces with the operator, and the environment, designed, constructed and arranged to operate together as a unit, such that a single failure or single operating error will not cause injury to personnel due to point of operation hazards. (63) Authorized person means one to whom the authority and responsibility to perform a specific assignment has been given by the employer. (64) Certification or certify means, in the case of design certification/validation, that the manufacturer has reviewed and tested the design and manufacture, and in the case of installation certification/validation and annual recertification/revalidation, that the employer has reviewed and tested the installation, and concludes in both cases that the requirements of 1910.217 (a) through (h) and appendix A have been met. The certifications are made to the validation organization. (65) Validation or validate means for PSDI safety systems that an OSHA recognized third-party validation organization: (i) For design certification/validation has reviewed the manufacturer's certification that the PSDI safety system meets the requirements of 1910.217 (a) through (h) and appendix A and the underlying tests and analyses performed by the manufacturer, has performed additional tests and analyses which may be required by 1910.217 (a) through (h) and appendix A, and concludes that the requirements of 1910.217 (a) through (h) and appendix A have been met; and (ii) For installation certification/validation and annual recertification/revalidation has reviewed the employer's certification that the PSDI safety system meets the requirements of 1910.217 (a) through (h) and appendix A and the underlying tests performed by the employer, has performed additional tests and analyses which may be required by 1910.217 (a) through (h) and appendix A, and concludes that the requirements of 1910.217 (a) through (h) and appendix A have been met. (66) Certification/validation and certify/validate means the combined process of certification and validation.