Ohio Admin. Code 3745-20-08 - Reporting, certification and permit application requirements
[Comment: For dates of non-regulatory government publications, publications of recognized organizations and associations, federal rules, and federal statutory provisions referenced in this rule, see paragraph (C) of rule 3745-20-01 of the Administrative Code titled "Referenced materials."]
(A) Any owner or operator of a new source to
which this chapter applies with the exception of sources subject to rules
3745-20-04(demolition
and renovation), 3745-20-09 (roadways), 3745-20-14 (insulating), and 3745-20-15
(spraying) of the Administrative Code, and which has an initial start up date
preceding November 20, 1990, was required to provide the following information
to the director postmarked or delivered by February 18, 1991. In the case of a
new source that does not have an initial start up date preceding November 20,
1990, the information shall be provided by the owner or operator, postmarked or
delivered, within ninety days of the initial start up date of that source. Any
owner or operator of an existing source was required to provide the following
information to the director within ninety days of November 20, 1990, unless the
owner or operator of the existing source has previously provided this
information to the director:
(1) A
description of the emission control equipment used for each process; and
.
(2) If a fabric filter device is used to
control emissions,
,
provide the following information:
(a)
The airflow permeability in cubic feet per minute per square foot if the fabric
filter device uses a woven fabric, and, if the fabric is synthetic, whether the
fill yarn is spun or not spun; and
.
(b) The
density in ounces per square yard, the minimum thickness in inches, and the
airflow permeability in cubic feet per minute per square foot, if the fabric
filter device uses a felted fabric.
(3) If a HEPA filter is used to control
emissions, the certified efficiency.
(4) For asbestos waste disposal handling
sources subject to rule
3745-20-05
of the Administrative Code, provide the following
information :
(a) A brief description
of each process that generates asbestos-containing waste material; and
.
(b) The average volume of asbestos-containing
waste material disposed of, measured in cubic yards per day; and
.
(c) The emission control methods used in all
stages of waste disposal; and
.
(d) The
type of disposal site or treatment site used for ultimate disposal, the name of
the site operator, and the name and location of the disposal site.
(5) For active waste disposal and
inactive waste disposal sites subject to rules
3745-20-06
and
3745-20-07
of the Administrative Code, provide the following
information :
(a) A brief description of
the site; and
.
(b) The
method or methods used to comply with the standard, or alternative procedures
to be used.
(B) Any changes in the information provided
for paragraph (A) of this rule by any existing source shall be provided to the
director, postmarked or delivered, within thirty days after the
change.
(C) All owners and
operators of sources except roadways, demolition and renovation, spraying, and
insulating materials shall comply with this paragraph. In addition to the
information required in paragraph (A) of this rule, the owner or operator of
each existing source or each new source which had an initial start up before
the effective date of this rule
November 18, 2002 shall provide the following
information in writing to the director within ninety
days after the effective date of this rule
by
February 18, 2003 . The following
information described in this rule must
shall be reported using the format provided in 40
CFR Part 61, Appendix A:
(1) Name and address
of the owner or operator.
(2) The
location of the source.
(3) The
type of hazardous air pollutants potentially emitted by the stationary
source.
(4) A brief description of
the nature, size, design, and method of operation of the stationary source
including the operating design capacity of the source. The description must
identify each point or fugitive source of emission for each hazardous air
pollutant.
(5) The average weight
per month of the hazardous materials being processed by the source over the
last twelve months preceding the date of the report.
(6) A description of the existing control
equipment for each emission point including the
following :
(a) Each control device for
each hazardous air pollutant; and
.
(b)
Estimated control efficiency (per cent) for each control device.
(7) A statement by the owner or
operator of the source as to whether the source can comply with the standards
within ninety days after the effective date.
(D) Any changes in the information provided
for paragraph (C) of this rule by any existing source shall be provided to the
director, postmarked or delivered, within thirty days after the
change.
(E) No person shall install
or operate a new source regulated under rule
3745-20-06,
3745-20-10,
3745-20-11,
or
3745-20-13
of the Administrative Code unless the owner or operator applies for and obtains
from the Ohio EPA one of the following as
applicable:
a permit-to-install and operate
pursuant to Chapter 3745-31 of the Administrative Code; or, a permit-to-install
pursuant to Chapter 3745-31 of the Administrative Code and a permit-to-operate
pursuant to Chapter 3745-77 of the Administrative Code, as applicable.
(1)
A
permit-to-install and operate pursuant to Chapter 3745-31 of the Administrative
Code.
(2)
A permit-to-install pursuant to Chapter 3745-31 of the
Administrative Code and a permit-to-operate pursuant to Chapter 3745-77 of the
Administrative Code.
Notes
Promulgated Under: 119.03
Statutory Authority: 3704.03(E)
Rule Amplifies: 3704.03(A), 3704.03(E)
Prior Effective Dates: 05/29/1990, 11/18/2002, 02/25/2004, 02/02/2007, 03/02/2012
State regulations are updated quarterly; we currently have two versions available. Below is a comparison between our most recent version and the prior quarterly release. More comparison features will be added as we have more versions to compare.
No prior version found.