49 CFR 180.411 - Acceptable results of tests and inspections.

Status message

There is 1 rule appearing in the Federal Register for 49 CFR Part 180. View below or at eCFR (GPOAccess)
§ 180.411 Acceptable results of tests and inspections.
(a) Corroded or abraded areas. The minimum thickness may not be less than that prescribed in the applicable specification.
(b) Dents, cuts, digs and gouges. For evaluation procedures, see CGA C-6 (IBR, see § 171.7 of this subchapter).
(1) For dents at welds or that include a weld, the maximum allowable depth is 1/2 inch. For dents away from welds, the maximum allowable depth is 1/10 of the greatest dimension of the dent, but in no case may the depth exceed one inch.
(2) The minimum thickness remaining beneath a cut, dig, or gouge may not be less than that prescribed in the applicable specification.
(c) Weld or structural defects. Any cargo tank with a weld defect such as a crack, pinhole, or incomplete fusion, or a structural defect must be taken out of hazardous materials service until repaired.
(d) Leakage. All sources of leakage must be properly repaired prior to returning a tank to hazardous materials service.
(e) Relief valves. Any pressure relief valve that fails to open and reclose at the prescribed pressure must be repaired or replaced.
(f) Liner integrity. Any defect shown by the test must be properly repaired.
(g) Pressure test. Any tank that fails to meet the acceptance criteria found in the individual specification that applies must be properly repaired.
[Amdt. 180-2, 54 FR 25032, June 12, 1989, as amended at 68 FR 75764, Dec. 31, 2003]

Title 49 published on 2014-10-01.

The following are only the Rules published in the Federal Register after the published date of Title 49.

For a complete list of all Rules, Proposed Rules, and Notices view the Rulemaking tab.

  • 2015-01-08; vol. 80 # 5 - Thursday, January 8, 2015
    1. 80 FR 1076 - Hazardous Materials: Harmonization With International Standards (RRR)
      GPO FDSys XML | Text
      DEPARTMENT OF TRANSPORTATION, Pipeline and Hazardous Materials Safety Administration
      Final rule.
      Effective Date: January 1, 2015. Voluntary compliance date: PHMSA is authorizing voluntary compliance beginning January 1, 2015. Delayed compliance date: Unless otherwise specified, compliance with the amendments adopted in this final rule is required beginning January 1, 2016. Incorporation by reference date: The incorporation by reference of certain publications listed in this rule is approved by the Director of the Federal Register as of January 1, 2015.
      49 CFR Parts 171, 172, 173, 175, 176, 178 and 180

This is a list of United States Code sections, Statutes at Large, Public Laws, and Presidential Documents, which provide rulemaking authority for this CFR Part.

This list is taken from the Parallel Table of Authorities and Rules provided by GPO [Government Printing Office].

It is not guaranteed to be accurate or up-to-date, though we do refresh the database weekly. More limitations on accuracy are described at the GPO site.


United States Code

Title 49 published on 2014-10-01

The following are ALL rules, proposed rules, and notices (chronologically) published in the Federal Register relating to 49 CFR Part 180 after this date.

  • 2015-01-30; vol. 80 # 20 - Friday, January 30, 2015
    1. 80 FR 5340 - Hazardous Materials: Adoption of Special Permits (MAP-21) (RRR)
      GPO FDSys XML | Text
      DEPARTMENT OF TRANSPORTATION, Pipeline and Hazardous Materials Safety Administration
      Notice of Proposed Rulemaking (NPRM)
      Comments must be received by March 31, 2015.
      49 CFR Parts 171, 172, 173, 174, 176, 177, 178, and 180