128 Neb. Admin. Code, ch. 3, § 010 - Toxicity characteristic

010.01 A solid waste (except manufactured gas plant waste) exhibits the characteristic of toxicity if, using the Toxicity Characteristic Leaching Procedure, Test Method 1311 in "Test Methods for Evaluating Solid Waste, Physical/Chemical Methods," EPA Publication SW-846, as incorporated by reference in Chapter 1, 003, the extract from a representative sample of the waste contains any of the contaminants listed in Table 3 of this Title which follows at concentrations equal to or greater than the respective value given in that Table. Where the waste contains less than 0.5 percent filterable solids, the waste itself, after filtering using the methodology outlined in Method 1311, is considered to be the extract for the purpose of this Chapter.

010.02 A solid waste that exhibits the characteristic of toxicity, has the DEQ/EPA Hazardous Waste Number specified in Table 3 of this Title which follows and corresponds to the toxic contaminant causing it to be hazardous.

TABLE 3 - MAXIMUM CONCENTRATION OF CONTAMINANTS FOR THE TOXICITY CHARACTERISTIC

EPA Hazardous Waste Number	Contaminant	Chemical Abstracts Service Number	Regulatory Level(mg/L)
D004	Arsenic ................................	7440-38-2	5.0
D005	Barium .................................	7440-39-3	100.0
D018	Benzene ................................	71-43-2	0.5
D006	Cadmium ................................	7440-43-9	1.0
D019	Carbon tetrachloride ...................	56-23-5	0.5
D020	Chlordane ..............................	57-74-9	0.03
D021	Chlorobenzene ..........................	108-90-7	100.0
D022	Chloroform .............................	67-66-3	6.0
D007	Chromium ...............................	7440-47-3	5.0
D023	o-Cresol ...............................	95-48-7	2200.0
D024	m-Cresol ...............................	108-39-4	2200.0
D025	p-Cresol ...............................	106-44-5	2200.0
D026	Cresol .................................		2200.0
D016	2,4-D ..................................	94-75-7	10.0
D027	1,4-Dichlorobenzene ....................	106-46-7	7.5
D028	1,2 Dichloroethane	107-06-2	0.5
D029	1,1-Dichloroethylene ...................	75-35-4	0.7
D030	2,4-Dinitrotoluene .....................	121-14-2	10.13
D012	Endrin .................................	72-20-8	0.02
D031	Heptachlor (and its epoxide) ...........	76-44-8	0.008
D032	Hexachlorobenzene ......................	118-74-1	10.13
D033	Hexachlorobutadiene ....................	87-68-3	0.5
D034	Hexachloroethane .......................	67-62-1	3.0
D008	Lead ...................................	7439-92-1	5.0
D013	Lindane ................................	58-89-9	0.4
D009	Mercury ................................	7439-97-6	0.2
D014	Methoxychlor ...........................	72-43-5	10.0
D035	Methyl ethyl ketone ....................	78-93-3	200.0
D036	Nitrobenzene ...........................	98-95-3	2.0
D037	Pentachlorophenol ......................	87-86-5	100.0
D038	Pyridine ...............................	110-86-1	15.0
D010	Selenium ...............................	7782-49-2	1.0
D011	Silver .................................	7440-22-4	5.0
D039	Tetrachloroethylene ....................	127-18-4	0.7
D015	Toxaphene ..............................	8001-35-2	0.5
D040	Trichloroethylene ......................	79-01-6	0.5
D041	2,4,5-Trichlorophenol ..................	95-95-4	400.0
D042	2,4,6-Trichlorophenol ..................	88-06-2	2.0
D017	2,4,5-TP (Silvex) ......................	93-72-1	1.0
D043	Vinyl Chloride .........................	75-01-4	0.2

¹ Quantitation limit is greater than calculated regulatory level. The quantitation limit therefore becomes the regulatory limit.

² If o-, m-, and p-Cresol concentrations cannot be differentiated, the total Cresol (D026) concentration is used. The regulatory level of total Cresol is 200 mg/L.

Notes

128 Neb. Admin. Code, ch. 3, § 010