Ohio Admin. Code 311-1-04.3 - Tactical shirt: construction specifications
(A) There shall be a long-sleeve and
short-sleeve tactical shirt. The construction specifications of this rule shall
apply to both shirts, except as specifically noted.
(B) Style: The tactical shirt shall be a full
cut, plain front, coat style shirt with shoulder straps and two bellows breast
pockets with mitered flaps;
(1) Long sleeves
shall have barrel cuffs,
(2) The
short sleeve shirt shall have hemmed sleeves that are approximately nine inches
long measured from the center of the shoulder seam.
(C) Collar:
(1) The collar points shall be three inches
long with sewn-in permanent collar stays;
(2) The collar height at the rear shall be
one and one-half inches;
(3) The
collar shall have topstitching one-quarter inch off the edge of the
collar;
(4) The collar stand shall
be one and five-eighths inches at rear, and the band shall be die cut and
interlined.
(D)
Shirtfront:
(1) The shirt shall have either a
plain front or a one and one-half inch wide placket front;
(2) The shirtfront shall have seven
black buttons and corresponding button
holes;
(3) The shirtfront shall
have permanent creases.
(E) Shoulder straps:
(1) The shoulder straps shall measure one and
three-fourths to two inches wide at the sleeve head, tapering to one and
one-half to one and five-eighths inches at the ends. The ends shall be pointed.
The length of the straps shall be graduated to conform to the size of shirt.
The straps shall be single-needle stitched to the shoulders, with the lines of
the stitching forming an "X";
(2)
Black buttons
Buttons shall be attached to the yoke, to correspond
to the buttonholes in the pointed ends of the shoulder straps.
(F) Badge piece: The shirt shall
have two small, reinforced, open, verticle
vertical
buttonholes spaced one and one-fourth inches apart, and centered vertically two
inches above the left breast pocket flap.
(G) Pockets: The shirt shall have two
pockets, measuring five inches wide and six and one-fourth inches long from the
bottom of the pocket to top of flap, having one inch mitered corners,
black buttons, and corresponding
buttonholes.
(H) Pocket flaps shall
be five and one-fourth inches long and two inches wide, with the lower corners
mitered one inch; black buttons shall be
centered three-fourths inch from bottom of flap.
(I) Yokes: The shirt shall have a two piece
yoke, three and one-fourth inches deep measured from the bottom of the shirt
collar.
(J) Cuff and vents: The
cuff of the long-sleeve shirt shall be two and three-eighths inches wide with
one black button; the sleeve vent shall be
five inches.
(K) Stitching:
(1) The shirt shall have single needle
stitching throughout, with all topstitching one-quarter inch off the edge;
(2) The sleeve insert and side
close felling shall be safety-stitched.
(3) The thread shall be
black, polyester core wrapped in cotton.
(L) Buttons shall be 19
ligne pearlescent black plastic.
(M) A care label shall be permanently sewn
into the shirttail.
(N) Mill: Propper International -
long-sleeve 13235 black, short sleeve 13230 black; Blauer Streetgear - long
sleeve 8701, short sleeve 8711; Fechheimer Command Wear - long sleeve 35R5810,
short sleeve 85R5810; or equivalent designs constructed from the fabric
prescribed in rule 311-1-04.1 of the Administrative Code.
Notes
Promulgated Under: 111.15
Statutory Authority: 311.26, 311.28
Rule Amplifies: 311.28
Prior Effective Dates: 12/15/2001
State regulations are updated quarterly; we currently have two versions available. Below is a comparison between our most recent version and the prior quarterly release. More comparison features will be added as we have more versions to compare.
No prior version found.