16 Tex. Admin. Code § 25.27 - Retail Electric Service Switchovers
(a)
Right to switchover.
(1) General principles.
A consumer has the right to switch retail electric service to any electric or
municipally owned utility that has the right to provide service in the area in
which the consumer's consuming facility is located, subject to the terms of any
contract for electric service entered into pursuant to the disconnecting
utility's tariff. Because a consuming facility for which a switchover is sought
can obtain electric service from the disconnecting utility prior to the
switchover, an electric or municipally owned utility shall give a switchover a
lower priority than the elimination of outages and requests for service to
consuming facilities that do not have service. Nevertheless, a switchover shall
be performed as soon as reasonably possible, and the disconnecting and
connecting utilities shall strive to take the actions required below more
quickly than the deadlines listed below. In addition, the disconnecting and
connecting utilities shall minimize any outages related to making a
switchover.
(2) Options and
availability. This section provides two switchover options: partial switchover
and full switchover. All subsections of this section apply to electric
utilities, while only subsections (a), (c), (e), and (g) of this section apply
to municipally owned utilities. The partial switchover option is not available
in a particular area prior to September 1, 1999 and prior to such time as both
the disconnecting and connecting utilities have approved tariffs for
transmission service at the transmission and primary and secondary distribution
voltage levels. Until the utilities have such approved tariffs, subsections (d)
and (e) of this section do not apply. In addition, the partial switchover
option is not available to the extent that it would reduce the state's
jurisdiction over a utility. The provisions for full switchovers in this
section become effective for a particular area once the electric utilities that
have a right to provide service in the area have tariffs in effect that are
consistent with this section.
(3)
Limitations and refunds. A consuming facility may not be switched more than
once every 12 months. A consumer or connecting utility who pays a switchover
fee does not waive the right to seek a refund on the basis that the switchover
fee was excessive. In addition, a connecting utility or consumer who buys
facilities pursuant to this section waives the right to seek a refund only if
it expressly agrees to waive that right.
(b) Definitions. As used in this section, the
following terms have the following meanings.
(1) Idle facilities--The disconnecting
utility's facilities that are used to serve only the consuming facility being
switched, as well as the easements for these facilities. For consuming
facilities served above 480 volts, idle facilities also include costs, or a
portion of costs, pertaining to the upgrade of transmission and distribution
facilities that were necessary to serve the consuming facility, if the current
or prior owner of the consuming facility agreed to pay the costs upon
switching. In all other respects, idle facilities do not include facilities
that were installed or are being used to serve more than one consuming
facility, including: facilities that were designed with a capacity greater than
necessary to serve the consuming facility being switched in order that
additional consuming facilities could be served using the facilities in the
future; and upgrades that were made to common facilities in order to serve the
consuming facility being switched.
(2) Common facilities--The disconnecting
utility's facilities that are used, installed, or designed to serve more than
one consuming facility, except as specified in the definition of idle
facilities.
(c)
Documentation. The requests, notices, offers, agreements, and switchover
requests provided for in this section must be in writing, unless otherwise
indicated.
(d) Notice of switchover
options. Upon receiving an oral switchover request, the disconnecting utility
shall at that time orally describe the two switchover options, including
stating that there is no charge for a partial switchover, stating that there
will be a switchover fee for a full switchover, stating that switchover
requests must be in writing, stating that written general information on
switchover fees will be provided within two working days, and providing a fax
number and mailing address to send the switchover request. Within two working
days of a switchover request that does not specify whether a partial or full
switchover is being requested, the disconnecting utility shall provide the
consumer a document describing the two switchover options, including a
statement that there is no charge for a partial switchover, specifying for a
full switchover the base charge and base charge adder and stating that the
facilities recovery charge will vary depending on the circumstances, and
providing the deadlines prescribed in subsection (f)(2)(C) of this subsection
for the disconnecting utility to notify the connecting utility after payment of
the switchover fee that the full switchover can proceed.
(e) Partial switchover.
(1) Description. Under the partial switchover
option, the connecting utility provides power to the consuming facility using
the disconnecting utility's transmission and/or distribution facilities. The
disconnecting utility shall provide the connecting utility transmission service
to the same point of delivery that the disconnecting utility provided
electricity to the consuming facility prior to the switchover. Except where
necessary or where the connecting utility requests it, all of the disconnecting
utility's facilities needed to serve the consuming facility prior to the
switchover shall remain in place. The disconnecting utility may not charge a
switchover fee for a partial switchover, except that it may charge the
connecting utility a cost-based fee where the connecting utility requests that
the disconnecting utility remove facilities that were needed by the
disconnecting utility to serve the consuming facility prior to the switchover.
In addition, the disconnecting utility may charge a switching customer any
account closing fee that applies to all departing customers, not just switching
customers.
(2) Procedure for
partial switchover. The disconnecting utility shall contact the connecting
utility within three working days of receiving a request for a partial
switchover in order to coordinate the switchover. The switchover shall occur
within eight working days of the disconnecting utility's receipt of the
request, unless the consumer agrees to a longer schedule or unless good cause
exists for not completing the switchover within eight working days. If the
switchover will not be completed within eight working days, then the
disconnecting utility must notify the consumer, with copies to the commission's
Office of Customer Protection and to the connecting utility, providing the
reasons why the switchover has been delayed and when the switchover will be
completed. This notice must be provided as soon as possible, by fax to the
commission's Office of Customer Protection, connecting utility, and, if
possible, the consumer.
(f) Full switchover. A full switchover
involves the disconnecting utility disconnecting its facilities and the
connecting utility installing and/or purchasing transmission and/or
distribution facilities to serve the consuming facility. If the consumer is a
tenant, the consumer must obtain the clear and specific agreement of the owner
or owner's agent to switch over the consuming facility and must provide it to
the disconnecting utility as an attachment to a notarized affidavit stating
that the consumer has obtained the owner's or owner's agent's agreement. This
subsection does not apply within municipalities exercising original
jurisdiction that enacted switchover rules by August 28, 1998 that provide for
more expeditious full switchovers than provided by this subsection.
(1) Switchover fee. The switchover fee
applies regardless of whether the consumer requesting the switchover has ever
received service from the disconnecting utility at the consuming facility. The
fee consists of a base charge and, where applicable, a base charge adder and
facilities recovery charge. The disconnecting utility may not include in the
switchover fee a charge for general administrative expenses related to closing
the consumer's account. However, the disconnecting utility shall charge a
switching customer any account closing fee that applies to all departing
customers, not just switching customers. Where the disconnecting utility is
allowed to charge for the original cost of facilities, it must deduct
contributions in aid of construction that apply to those facilities.
Accumulated depreciation shall be calculated using the depreciation rates that
are currently used to book depreciation. Upon the payment of the switchover fee
or purchase, or refusal of an offer to purchase, under the circumstances
described in subparagraph (B)(i) of this paragraph, any construction charges
owed by the consumer, pursuant to a contract entered into after the effective
date of this subsection, for idle facilities used to provide service to the
consuming facility being switched are extinguished.
(A) Base charge and base charge adder. A base
charge applies to the switchover of a consuming facility served at 480 volts or
less. The base charge is equal to the cost of removing any meter and drop line
used to serve the consuming facility, and shall be specified in the
disconnecting utility's tariff. The switchover fee shall not include the
original cost less depreciation and gross salvage of the meter and drop line
for switchovers for which the base charge applies. A base charge adder that is
less than the base charge must also be specified in the tariff to cover the
situation where a consumer switches more than one consuming facility on the
same premises at the same time. The base charge adder is equal to the cost of
removing any meter and drop line used to serve each additional consuming
facility.
(B) Facilities recovery
charge. The purpose of the facilities recovery charge is to recover costs
related to idle facilities, other than meter and drop line costs covered by a
base charge or base charge adder.
(i)
Availability of facilities recovery charge. The disconnecting utility may not
impose a facilities recovery charge for idle facilities if the connecting
utility or consumer purchases the idle facilities at a price equal to net book
value and signs an agreement indemnifying the disconnecting utility from
liability for the facilities after the purchase of the facilities. Before a
consumer can purchase the facilities, it must prove that it has the financial
resources to protect the disconnecting utility from liability risks resulting
from the sale. Where more than one consumer requests a switchover, the
disconnecting utility may not impose a facilities recovery charge for idle
facilities if the connecting utility purchases the idle facilities and the
common facilities used to serve the consuming facilities being switched, but
not used to serve any consuming facilities not being switched, at a price equal
to replacement cost less depreciation and signs an indemnity agreement.
Replacement cost is equal to: the average original cost of like facilities
installed in the most recent full calendar year for which information is
available, that would be necessary to serve the consuming facilities being
switched if facilities were first installed to serve the consuming facilities
at the time of the switchover requests; plus the cost of easements for the
facilities if the easements were obtained at the time of the switchover
requests. The disconnecting utility also may not impose a facilities recovery
charge if it refuses an offer to purchase under the conditions described in
this subparagraph.
(ii) Components
of facilities recovery charge. The facilities recovery charge consists of the
net book value (original cost less depreciation) less net salvage (gross
salvage less cost of removal) of the idle facilities. In determining the net
book value of the facilities, the original cost of the specific facilities
should be used. If the original cost of the specific facilities is not
available, the installation date of the facilities shall be determined or
estimated and the average original cost of like facilities installed by the
disconnecting utility in that year shall be used. If average original cost
information is not available for the year in which the idle facilities were
installed, then the average original cost of like facilities installed in the
most recent full calendar year for which information is available shall be used
and shall be deflated to the installation date of the idle facilities. Where
average original cost information is used, the average original cost
information shall be determined using the information for the operating
division in which the consuming facility to be switched is located, if the
disconnecting utility maintains original cost information by
division.
(C) Labor
charges. Labor charges for removing facilities are limited to a reasonable
estimate of the direct labor cost (salary, insurance, pension, payroll taxes,
etc.) for the time of persons needed to remove the facilities. No allocation of
general overhead labor is allowed, but any necessary supervisory or engineering
labor specific to the removal of the facilities may be included.
(D) Quantification of charges. The
calculation of the base charge, base charge adder, and facilities recovery
charge may involve the making of estimates. To the extent that there is a range
of reasonable estimates for a particular charge, the estimate at the low end of
the range should be used, so that the amount of the switchover fee will be
minimized, but still be reasonable and in conformance with this section. Unless
the consumer agrees otherwise, there will be no refund or surcharge if the
actual cost of performing the switchover is less than or greater than the
switchover fee. Instead of a utility-specific base charge and base charge
adder, the commission may, through the issuance of an order, establish a single
base charge and a single base charge adder to be used by all electric
utilities. Likewise, the commission may, through the issuance of an order,
establish fixed dollar charges for components of the facilities recovery
charge.
(E) Payment of switchover
fee and other charges. Before the connecting utility provides service, the
disconnecting utility has the right to receive payment of the switchover fee
and any other outstanding charges. The connecting utility shall not reimburse
the consumer for the switchover fee, and may pay the switchover fee only if the
consumer agrees prior to the connecting utility's payment of the fee that the
consumer will reimburse the connecting utility for the fee. The agreement must
contain a plan for the payment of the fee within a reasonable period of
time.
(2) Procedure for
full switchover.
(A) Notice of switchover fee
and procedure. Upon receiving a request for a full switchover, the
disconnecting utility must provide the consumer a document that quantifies the
switchover fee within 15 working days. This document must be in 12 point,
non-bold type and must itemize the base charge, base charge adder, and the
facilities recovery charge of the switchover fee. In addition, the document
must itemize the components of the facilities recovery charge, including a
description of the idle facilities, the installation dates of the idle
facilities, the original cost of the idle facilities, the accumulated
depreciation associated with the idle facilities, the depreciation rates used
to calculate the accumulated depreciation, transportation charges for removing
the idle facilities, labor rates, labor hours for removing the idle facilities,
and the gross salvage value of the idle facilities. The document must also
state immediately below these itemizations, in bold, and in not less than 12
point type: "(Disconnecting utility) may not impose a facilities recovery
charge under the circumstances described in Public Utility Commission of Texas
Substantive Rule §25.27(f)(1)(B)(i). On request, you will be provided a
copy of Rule §25.27."
(B) Sale
of both common and idle facilities. If a group of consumers request
switchovers, the switchovers may necessitate that the connecting utility
acquire common and idle facilities in that case. Within 15 working days of
receipt of a request from the connecting utility, the disconnecting utility
must provide by fax and mail a detailed, reasonable estimate of replacement
cost less depreciation for the idle facilities and the common facilities used
to serve the consuming facilities to be switched, but not used to serve any
consuming facilities not being switched.
(C) Offer to purchase facilities. Within five
working days of receipt of an offer to purchase idle and/or common facilities
under the conditions described in paragraph (1)(B)(i) of this subsection, the
disconnecting utility must notify the connecting utility by fax, with copies by
mail or fax to the consumers, whether it accepts or rejects the offer. If the
disconnecting utility rejects the offer, it must also provide revised
switchover fees that delete the facilities recovery charges, at the same time
that it provides notice of rejection of the offer.
(D) Payment of switchover fee and outstanding
balances. Until the switchover fee and all outstanding balances are paid to the
disconnecting utility, neither the disconnecting utility nor the connecting
utility is under any obligation to take steps to make the switchover, and the
connecting utility must not provide service to the consuming facility being
switched until it receives notice from the disconnecting utility that the
switchover can proceed. The disconnecting utility must within the following
deadlines from the receipt of payment, notify the connecting utility by fax
that the switchover can proceed: two working days for payment by cash, money
order, cashier's check, or, if accepted by the disconnecting utility for bill
payment, credit card, and five working days for payment by personal check or
other forms of payment.
(E)
Deadline for full switchover. Once the disconnecting utility notifies the
connecting utility that the switchover can proceed and once the connecting
utility notifies the disconnecting utility by fax that the consumer has
satisfied the conditions for service from the connecting utility, the
switchover must be completed within ten working days unless the consumer agrees
to a longer schedule, good cause exists for the disconnecting utility not being
able to complete the switchover within ten working days, or the connecting
utility needs more time to install facilities, so long as the connecting
utility complies with the rules concerning responses to requests for service
that apply regardless of whether the request relates to a switchover. If the
disconnecting utility does not meet the deadline, then the disconnecting
utility must notify the consumer, with copies to the commission's Office of
Customer Protection and the connecting utility, providing the reasons why the
switchover has been delayed and when the switchover will be completed. This
notice must be provided as soon as possible, by fax to the commission's Office
of Customer Protection, the connecting utility and, if possible, the
consumer.
(F) Consumer's failure to
pay. The consumer may continue to incur charges for retail electric service
from the disconnecting utility after the consumer pays the switchover fee and
outstanding balances, and may have an unfulfilled contractual obligation that
requires future payment of charges to the disconnecting utility. The
disconnecting utility has the right to payment of these charges consistent with
§ 23.45 of this title (relating to Billing). If the consumer has not paid
the charges within the appropriate time, the disconnecting utility may notify
the connecting utility of the consumer's failure to pay and request that the
consumer be disconnected, and must at the same time provide a copy of the
notice to the consumer, by fax if possible. Upon receipt of such notification
and request and upon receipt from the disconnecting utility of an agreement
indemnifying the connecting utility from liability for improper cause for
disconnection of service, the connecting utility must disconnect the consumer's
service in compliance with the procedures in § 23.46 of this title
(relating to Discontinuance of Service). Immediately upon verification of the
consumer's correction of its failure, the disconnecting utility must notify the
connecting utility by fax that the consumer's failure has been corrected, and
the connecting utility must immediately reconnect service. The connecting
utility shall charge a switching customer any disconnection or reconnection fee
that applies to all disconnected customers, not just those who have been
disconnected pursuant to this subparagraph.
(g) Complaint concerning a switchover. A
consumer complaint to the commission concerning a switchover shall be handled
according to §23.41(c) of this title (relating to Customer Relations),
with the following modification. The commission will forward a complaint that
it receives to both the disconnecting utility and the connecting utility, and
both utilities must provide an initial response within the deadline specified
in §23.41(c).
(h) Compliance
tariff provisions. An electric utility that has the right to serve in an area
for which another utility also has the right to provide retail electric service
shall include in its tariff a section entitled "Retail Electric Service
Switchovers". Immediately below this title, the tariff shall state: "A request
to switch service to a consuming facility to another utility that has the right
to serve the facility shall be handled pursuant to Public Utility Commission of
Texas Substantive Rule §25.27, a copy of which will be provided upon
request." Immediately below this statement, the tariff must specify the
electric utility's base charge and base charge adder. The electric utility's
tariff shall not include any other information addressing retail electric
service switchovers.
Notes
State regulations are updated quarterly; we currently have two versions available. Below is a comparison between our most recent version and the prior quarterly release. More comparison features will be added as we have more versions to compare.
No prior version found.