This section establishes specific procedures for the
measurement of sound levels from exhaust systems at a distance of 20 inches
(0.5 meter) from the exhaust outlet. The procedures of subsections (3), (4) and
(5) of this section shall not be used for exhaust systems which utilize the
introduction of water to the exhaust gas flow for the purpose of muffling the
exhaust noise levels, or systems which exhaust the gas flow directly into
water.
(1) For the purposes of this
section "vehicle" means any motor driven contrivance used as a means of
transportation or recreation off of public highways.
(2) Initial inspection. An initial inspection
of the vehicle exhaust system shall be conducted to determine if the following
defects or modifications exist:
(a) The
absence of a muffler;
(b) The
presence of a muffler cut-out, bypass, or similar device which is not standard
or normal equipment for the exhaust system being inspected;
(c) Defects in the exhaust system including,
but not limited to, pinched outlets, and holes or rusted through areas of the
muffler or pipes;
(d) The presence
of equipment which will produce excessive or unusual noise from the exhaust
system.
If the above defects are observed and are a violation of the
muffler integrity standards established for the type of vehicle which is being
inspected, then a citation shall be issued in accordance with the enforcement
section of the applicable regulation.
An evaluation of the vehicle sound level shall also be made by
the enforcement officer, using the human ear as a sensing device.
If the exhaust noise is discernibly louder than the engine
noise, or if any of the defects or modifications described above exist but are
not violations of applicable regulations, the enforcement officer shall request
the vehicle operator to submit the vehicle to any measurement procedures
described in this chapter which are applicable to the type of vehicle being
inspected. If the operator refuses to submit the vehicle to these measurement
procedures, he shall be in violation of this chapter.
(3) Test site and instrumentation
set up. The test site and instrumentation shall be set up as follows:
(a) The test site shall be a flat, open area
free of large, sound-reflecting surfaces (other than the surface on which the
vehicle is resting), such as signboards, buildings, large docks, hillsides, or
other vehicles, located within a 16-foot (5-meter) radius of the vehicle being
tested and the location of the microphone. The vehicle shall not be on a hoist,
rack, or over a pit. Testing shall not occur within a shop or building. Nobody
shall stand in the measurement area, except the observer and the vehicle
operator.
(b) The microphone shall
be at the same height as the center of the exhaust outlet if possible, but no
closer to any surface than 8 inches (0.2 meter). The microphone shall be
positioned with its longitudinal axis parallel to the ground, 20 +- 1 inches
(0.5 meter) from the edge of the exhaust outlet, and 45 +- 10 degrees from the
axis of the outlet. For exhaust outlets located inboard from the vehicle body,
the microphone shall be located at the above specified angle and at least 8
inches (0.2 meter) from the nearest part of the vehicle.
For vehicles provided with exhaust outlets spaced more than 12
inches (0.3 meter) apart, measurements shall be made for each outlet as if it
were the only one, and the highest level shall be recorded. If the exhaust
outlets are less than twelve inches (0.3 meter) apart, a single measurement
shall be made for any one of the outlets.
For vehicles with a vertical exhaust, the microphone shall be
placed at a height of 48 +- 2 inches (1.2 meter). Its axis shall be vertical
and oriented upwards. It shall be placed at a distance of 20 +- 1 inches (0.5
meter) from the side of the vehicle nearest the exhaust outlet.
For vehicles with the exhaust system outlet near the engine,
the engine hood (if one exists) should be closed as much as possible to reduce
engine noise.
If a measuring device is attached to the exhaust outlet and the
microphone to maintain proper distance, insure that no vibrations from the
vehicle shall be transmitted to the instrument.
(4) Vehicle operation. The vehicle shall be
operated as follows:
(a) Controlled ignition
vehicles. The engine shall be operated at a normal operating temperature with
transmission in park or neutral. Sound level measurements shall be made at
three-fourths (75 percent) of the RPM for rated horsepower +- 100 RPM of meter
reading.
(b) Vehicles with
motorcycle engines. The engine shall be operated at normal operating
temperatures with the transmission in neutral. If no neutral is provided, the
vehicle shall be operated either with the rear wheel or wheels 2-4 inches (5-10
centimeters) clear of the ground, or with the drive chain or belt removed. The
sound level measurement shall be made with the engine speed stabilized at one
of the following values:
(i) If the engine
data is available, test the vehicle at one-half (50 percent) of the RPM for
maximum rated horsepower +- 100 RPM.
(ii) If the engine data is not available, and
if the vehicle has a tachometer showing the manufacturer's recommended maximum
engine speed ("red line"), test the vehicle at 60 percent of the "red line" RPM
+- 100 RPM.
(iii) If the engine
data and red line RPM are not available, test the vehicle at:
(A) 3500 +- 100 RPM for engines with total
cylinder displacement between 0-950 cc (0-58
in.3).
(B) 2800 RPM +- 100 RPM for engines with
total cylinder displacement greater than 950 cc (58
in.3).
(c) Diesel engine vehicles. The engine shall
be operated at normal operating temperatures with transmission in park or
neutral. Sound level measurements shall be made at the vehicle's maximum
governed no-load speed. If the engine is not provided with a governor, the
vehicle shall be operated in the same manner as a vehicle with a controlled
ignition.
(5)
Measurement. The exhaust system sound level shall be measured as follows:
(a) The sound level meter shall be set for
slow response and on the "A" weighting scale.
(b) The sound level meter shall be observed
during the full cycle of engine acceleration-deceleration. The recorded sound
level shall be the highest value obtained at the appropriate, constant engine
speed as specified in subsection (4) of this section, and shall exclude peaks
due to unrelated ambient noise, engine noise, or extraneous impulsive-type
noise.
(c) At least two
measurements shall be made, and the reported sound level shall be the average
of the two highest readings which are within one dBA of each other.
