10 CFR Appendix C to Part 110, Illustrative List of Gaseous Diffusion Enrichment Plant Assemblies and Components Under NRC Export Licensing Authority
In the gaseous diffusion method of uranium isotope separation, the main technological assembly is a special porous gaseous diffusion barrier, heat exchanger for cooling the gas (which is heated by the process of compression), seal valves and control valves, and pipelines. Inasmuch as gaseous diffusion technology uses uranium hexafluoride (UF6), all equipment, pipeline and instrumentation surfaces (that come in contact with the gas) must be made of materials that remain stable in contact with UF6. A gaseous diffusion facility requires a number of these assemblies, so that quantities can provide an important indication of end use.
The auxiliary systems, equipment, and components for gaseous diffusion enrichment plants are the systems of plant needed to feed UF6 to the gaseous diffusion assembly to link the individual assemblies to each other to form cascades (or stages) to allow for progressively higher enrichments and to extract the “product” and “tails” UF6 from the diffusion cascades. Because of the high inertial properties of diffusion cascades, any interruption in their operation, and especially their shut-down, leads to serious consequences. Therefore, a strict and constant maintenance of vacuum in all technological systems, automatic protection for accidents, and precise automated regulation of the gas flow is of importance in a gaseous diffusion plant. All this leads to a need to equip the plant with a large number of special measuring, regulating, and controlling systems.
Normally UF6 is evaporated from cylinders placed within autoclaves and is distributed in gaseous form to the entry point by way of cascade header pipework. The “product” and “tails” UF6 gaseous streams flowing from exit points are passed by way of cascade header pipework to either cold traps or to compression stations where the UF6 gas is liquified prior to onward transfer into suitable containers for transportation or storage. Because a gaseous diffusion enrichment plant consists of a large number of gaseous diffusion assemblies arranged in cascades, there are many kilometers of cascade header pipework, incorporating thousands of welds with substantial amounts of repetition of layout. The equipment, components, and piping systems are fabricated to very high vacuum and cleanliness standards.
The items listed below either come into direct contact with the UF6 process gas or directly control the flow within the cascade. All surfaces which come into contact with the process gas are wholly made of, or lined with, UF6-resistant materials. For the purposes of this appendix, the materials resistant to corrosion by UF6 include copper, copper alloys, stainless steel, aluminum, aluminum oxide, aluminum alloys, nickel or alloys containing 60 percent or more nickel and fluorinated hydrocarbon polymers.
1. Assemblies and components especially designed or prepared for use in gaseous diffusion enrichment.
(a) Especially designed or prepared thin, porous filters, with a pore size of 10-100 nm, a thickness of 5 mm or less, and for tubular forms, a diameter of 25 mm or less, made of metallic, polymer or ceramic materials resistant to corrosion by UF6 (See Note in § 2 of this appendix).
(b) Especially prepared compounds or powders for the manufacture of such filters. Such compounds and powders include nickel or alloys containing 60 percent or more nickel, aluminum oxide, or UF6-resistant fully fluorinated hydrocarbon polymers having a purity of 99.9 percent by weight or more, a particle size less than 10 µm, and a high degree of particle size uniformity, which are especially prepared for the manufacture of gaseous diffusion barriers.
Especially designed or prepared hermetically sealed vessels for containing the gaseous diffusion barrier, made of or protected by UF6-resistant materials (See Note in § 2 of this appendix).
Especially designed or prepared compressors or gas blowers with a suction volume capacity of 1 m 3 per minute or more of UF6, and with a discharge pressure of up to 500 kPa, designed for long-term operation in the UF6 environment, as well as separate assemblies of such compressors and gas blowers. These compressors and gas blowers have a pressure ratio of 10:1 or less and are made of, or protected by, materials resistant to UF6 (See Note in § 2 of this appendix).
Especially designed or prepared vacuum seals, with seal feed and seal exhaust connections, for sealing the shaft connecting the compressor or the gas blower rotor with the driver motor so as to ensure a reliable seal against in-leaking of air into the inner chamber of the compressor or gas blower which is filled with UF6. Such seals are normally designed for a buffer gas in-leakage rate of less than 1000 cm 3 per minute.
Especially designed or prepared heat exchangers made of or protected by UF6 resistant materials (see Note to § 2 of this appendix) and intended for a leakage pressure change rate of less than 10 Pa per hour under a pressure difference of 100 kPa.
2. Auxiliary systems, equipment, and components especially designed or prepared for use in gaseous diffusion enrichment.
Note: The items listed below either come into direct contact with the UF6 process gas or directly control the flow within the cascade. Materials resistant to corrosion by UF6 include copper, copper alloys, stainless steel, aluminum, aluminum oxide, aluminum alloys, nickel or alloys containing 60 percent or more nickel, and fluorinated hydrocarbon polymers.
Especially designed or prepared process systems or equipment for enrichment plants made of, or protected by, materials resistant to corrosion by UF6, including:
(1) Feed autoclaves, ovens, or systems used for passing UF6 to the enrichment process;
(2) Desublimers, cold traps, or pumps used to remove UF6 from the enrichment process for subsequent transfer upon heating;
(3) Solidification or liquefaction stations used to remove UF6 from the enrichment process by compressing and converting UF6 to a liquid or solid form;
(4) “Product” or “tails” stations used for transferring UF6 into containers.
Especially designed or prepared piping systems and header systems for handling UF6 within the gaseous diffusion cascades. This piping network is normally of the “double” header system with each cell connected to each of the headers.
(a) Especially designed or prepared vacuum manifolds, vacuum headers and vacuum pumps having a suction capacity of 5 m 3 per minute or more.
(b) Vacuum pumps especially designed for service in UF6-bearing atmospheres made of, or protected by, materials resistant to corrosion by UF6 (See Note to this section). These pumps may be either rotary or positive displacement, may have fluorocarbon seals, and may have special working fluids present.
Especially designed or prepared bellows-sealed valves, manual or automated, shut-off or control valves, made of, or protected by, materials resistant to corrosion by UF6, for installation in main and auxiliary systems of gaseous diffusion enrichment plants.
Especially designed or prepared mass spectrometers capable of taking on-line samples from UF6 gas streams and having all of the following:
(a) Capable of measuring ions of 320 atomic mass units or greater and having a resolution of better than 1 part in 320;
(b) ion sources constructed of or protected by nickel, nickel-copper alloys with a nickel content of 60 percent or more by weight, or nickel-chrome alloys;
(c) electron bombardment ionization sources; and
(d) having a collector system suitable for isotopic analysis.
3. Any other components especially designed or prepared for use in a gaseous diffusion enrichment plant or in any of the components described in this appendix.
Title 10 published on 10-May-2017 03:48
The following are ALL rules, proposed rules, and notices (chronologically) published in the Federal Register relating to 10 CFR Part 110 after this date.