Fla. Admin. Code Ann. R. 62-297.310 - General Emissions Test Requirements
(1) Applicability. Unless otherwise stated in
a specific rule, permit, or other order, the general requirements set forth in
subsections 62-297.310(2) through
(10), F.A.C., shall be used for regulated
stationary sources' emissions tests for comparison with air pollution
emission-limiting standards that are enforceable under state law. An emissions
test is an emissions rate test, a concentration test, or an opacity
test.
(2) Required Number of Test
Runs. For emission rate or concentration limitations, an emissions test shall
consist of three valid test runs to determine the total air pollutant emission
rate or concentration through the test section of the stack or duct. A valid
test run is a test run that meets all requirements of the applicable test
method. An emissions test shall also consist of three distinct determinations
of any applicable process parameters corresponding to the three distinct test
run time periods during which the emission rate or concentration was measured
when such data are needed in conjunction with emissions data to compare the
emissions test results with the applicable emission limiting standards. Such
data shall be obtained pursuant to subsection
62-297.310(6),
F.A.C. The three required test runs shall be completed within one consecutive
five-day period. In the event that a sample is lost or one of the three runs
must be discontinued because of circumstances beyond the control of the owner
or operator, and a valid third run cannot be obtained within the five day
period allowed for the test, results of the two valid runs shall be accepted,
provided that the arithmetic mean of the results of the two valid runs is at
least 20% below the allowable emission limiting standard.
(3) Operating Conditions during Emissions
Testing. Testing of emissions shall be conducted with the emissions unit
operating at the testing capacity as defined below. If it is impracticable to
test at the testing capacity, an emissions unit may be tested at less than the
testing capacity. If an emissions unit is tested at less than the testing
capacity, another emissions test shall be conducted and completed no later than
60 days after the emissions unit operation exceeds 110% of the capacity at
which its most recent emissions test was conducted.
(a) Combustion Turbines. (Reserved)
(b) All Other Sources. Testing capacity is
defined as at least 90 percent of the maximum operation rate specified by the
permit.
(4) Calculation
of Emission Rate or Concentration. The emission rate or concentration used for
comparison with the relevant standard shall be the arithmetic average of the
emission rate or concentration determined by each of the three valid test runs
unless otherwise specified in an applicable rule or test method. Data collected
during periods of soot blowing shall not be excluded from any calculation of
emission rate or concentration.
(5)
Required Sampling Times and Observation Periods. Unless otherwise specified in
an applicable test method, rule, permit, or other order, the owner or operator
shall conduct emissions tests in accordance with the following procedures:
(a) Emission Rate or Concentration Tests. The
required sampling time for each test run shall be no less than one hour and no
greater than four hours, and the sampling time at each sampling point shall be
of equal intervals of at least two minutes, except that for operations that are
typically completed within less than the minimum required sampling time, the
duration of each test run shall include each occurrence of the operation during
the minimum required sampling time. The test period shall include the period of
typical operation during which the highest representative emissions are
expected to occur.
(b) Opacity
Tests. When EPA Method 9 is specified as the applicable opacity test method,
the required minimum period of observation for a visible emissions test shall
be 60 minutes for emissions units that are subject to a multiple-valued opacity
standard and 30 minutes for all other emissions units, except that for batch,
cyclical processes, or other operations that are typically completed within
less than the minimum observation period, the period of observation shall
include each occurrence of the operation during the minimum observation period.
The opacity test observation period shall include the period during which the
highest opacity emissions can reasonably be expected to
occur.
(6) Determination
of Process Parameters.
(a) Required Process
Equipment. The owner or operator of an emissions unit for which emissions tests
are required shall install, operate, and maintain equipment or instruments
necessary to determine process parameters, when such data are needed in
conjunction with emissions data to compare emissions test results with
applicable emission limiting standards.
(b) Accuracy of Process Measurement
Equipment. Equipment or instruments used to directly or indirectly determine
process parameters shall be calibrated and adjusted so as to determine the
value of the process parameter to within 10 percent of its true
value.
(7) Required
Emissions Testing Facilities.
(a) The owner or
operator of an emissions unit, for which an emissions test other than a visible
emissions test is required, shall provide emissions testing facilities that
meet the requirements of 40
CFR 60.8(e), adopted and
incorporated in Rule 62-204.800, F.A.C.
(b) Permanent Emissions Testing Facilities.
The owner or operator of an emissions unit, for which an emissions test other
than a visible emissions test is required on at least an annual basis, shall
install and maintain permanent emissions testing facilities.
(c) Temporary Emissions Testing Facilities.
The owner or operator of an emissions unit that is not required to conduct an
emissions test on at least an annual basis may use permanent or temporary
emissions testing facilities. If the owner or operator chooses to use temporary
emissions testing facilities on an emissions unit, and the Department elects to
test the unit, such temporary facilities shall be installed on the emissions
unit within 5 days of a request by the Department and remain on the emissions
unit until the test is completed.
(8) Frequency of Emissions Tests. The
following provisions apply only to those emissions units that are subject to an
emissions-limiting standard for which emissions testing is required.
(a) Annual Emissions Tests Required.
1. Where used in Rules
62-210.310,
62-297.310, or Chapter 62-296,
F.A.C., to refer to frequency of required emissions tests, the terms "annual, "
"annually, " and "annually thereafter" shall mean no less frequently than once
every calendar year (January 1 - December 31).
2. Unless exempted by subparagraph
62-297.310(8)(a)
5., F.A.C., the owner or operator shall have an emissions unit tested annually
for each of the following pollutants that has an emissions-limiting standard
for which emissions testing is required:
a.
Each hazardous air pollutant regulated by 40 C.F.R. Part 61, adopted and
incorporated by reference at Rule
62-204.800, F.A.C.;
and,
b. Any other regulated air
pollutant, as defined at Rule
62-210.200, F.A.C., or a
pollutant designated as a surrogate to a regulated air pollutant by an
applicable rule or order, if allowable emissions equal or exceed 100 tons per
year.
3. Unless exempted
by subparagraph 62-297.310(8)(a)
5., F.A.C., the owner or operator shall have an emissions unit tested annually
for visible emissions, if there is an applicable standard other than the
general opacity standard of subparagraph
62-296.320(4)(b)
1., F.A.C.
4. Unless exempted by
subparagraph 62-297.310(8)(a)
5., F.A.C., the owner or operator shall have an emissions unit tested annually
if a rule, permit or other order issued after March 9, 2015, requires an
initial emissions test but is silent as to the frequency of additional testing.
A rule, permit, or other order that states that no further testing is required
after an initial test, or which expressly lists or describes the tests that
shall be conducted annually, is not considered silent as to the frequency of
additional testing. Annual testing is not required where a permit or other
order issued prior to March 9, 2015, is silent as to the frequency of
additional testing.
5. Exemptions
from subparagraphs 62-297.310(8)(a)
2., 3., and 4., F.A.C.
a. An annual emissions
test shall not be required for any pollutant for which a rule, permit, or other
order requires emissions testing at some other specific frequency. If multiple
applicable rules, permits, or other orders, other than subparagraphs
62-297.310(8)(a)
2., 3., and 4., F.A.C., require different testing frequencies, testing must
comply with the frequency requirements of each such rule, permit, or
order.
b. An annual emissions test
shall not be required for any pollutant for which a rule, permit, or other
order requires that the pollutant emissions be measured by a continuous
emission monitoring system and, either that system meets the performance
specifications and quality assurance and quality control measures of 40 CFR
part 60, adopted and incorporated in Rule
62-204.800, F.A.C., or that
system meets the performance specifications and quality assurance and quality
control measures of 40 C.F.R. part 75, adopted and incorporated in Rule
62-204.800, F.A.C.
c. An annual emissions test shall not be
required for visible emissions for which a rule, permit, or other order
requires that emissions be measured by a continuous opacity monitoring system,
and that system meets the performance specifications and quality assurance and
quality control measures of 40 C.F.R. part 60, adopted and incorporated in Rule
62-204.800, F.A.C., and the
manufacturer's recommended quality assurance and quality control
measures.
d. An annual emissions
test shall not be required for any emissions unit that operated for 400 hours
or less (including during startup and shutdown) during the calendar year. If an
emission unit operates for more than 400 hours during the calendar year, an
emissions test shall be completed no later than 60 days after the emissions
unit's annual operation exceeds 400 hours, or by the end of the calendar year,
whichever is later.
e. An annual
emissions test shall not be required for any emissions unit with emissions
generated solely from the combustion of fuel, provided that the emissions unit
does not burn any liquid fuel or solid fuel or fuel blend for more than 400
hours combined, other than during startup, during the calendar year. If an
emissions unit's liquid fuel or solid fuel or fuel blend burning exceeds 400
hours combined during the calendar year, other than during startup, an
emissions test shall be completed no later than 60 days after the emissions
unit's liquid fuel or solid fuel or fuel blend burning exceeds 400 hours
combined, or by the end of the calendar year, whichever is later.
f. An annual emissions test shall not be
required for each fuel-specific emissions limit, provided the fuel or fuel
blend subject to a fuel-specific limit was not burned for more than 400 hours,
other than during startup, during the calendar year. If an emissions unit burns
a fuel or fuel blend subject to a fuel-specific emission limit for more than
400 hours, other than during startup, during the calendar year, an emissions
test for that fuel or fuel blend shall be completed no later than 60 days after
the unit's burning of that fuel or fuel blend exceeds 400 hours, or by the end
of the calendar year, whichever is later.
g. An emissions unit shall not be required to
start up for the sole purpose of conducting an emissions test to meet the
frequency requirements of subsection
62-297.310(8),
F.A.C. In such a case, an emissions test shall be completed no later than 60
days after the emissions unit next starts up.
h. An emissions unit permitted to burn
multiple fuels or fuel blends shall not be required to switch fuels for the
sole purpose of conducting an annual emissions test to meet the frequency
requirements of subsection
62-297.310(8),
F.A.C. In such a case, an emissions test shall be completed no later than 60
days after a switch is made to burn the fuel or fuel blend for which testing is
required.
i. An annual emissions
test for visible emissions shall not be required for emissions units exempted
from air permitting pursuant to paragraph
62-210.300(3)(a) or
(b), F.A.C.; emissions units determined to be
insignificant pursuant to paragraph
62-213.430(6)(b),
F.A.C.; or emissions units authorized pursuant to the general permit provisions
in subsection 62-210.300(4),
F.A.C., unless the general permit specifically requires such
testing.
(b)
Emissions Tests Prior to Obtaining an Air Operation Permit.
1. Unless exempted by subparagraph
62-297.310(8)(b)
3., F.A.C., prior to obtaining an initial or renewal air operation permit for
any emissions unit that is subject to any emission-limiting standard, the owner
or operator shall have an emissions test conducted for each such standard to
assist in providing reasonable assurance, per Rule
62-4.070, F.A.C., that the
emission-limiting standard can be met and shall submit the test report as
specified in subsection
62-297.310(10),
F.A.C. For an emissions unit at a Title V source, such prior emissions testing
is not required provided that an emissions testing compliance plan is included
in the Title V permit.
2. For the
purpose of renewal of an air operation permit, the owner or operator may
satisfy the requirements of subparagraph
62-297.310(8)(b)
1., F.A.C., for any emissions unit by submitting the most recent emissions
test, as specified in subsection
62-297.310(10),
F.A.C., provided such test occurred within the term of the current operating
permit.
3. Exemptions from
subparagraph 62-297.310(8)(b)
1., F.A.C.
a. An emissions test shall not be
required for any pollutant for which a rule, permit, or other order requires
that the emissions be measured by a continuous emission monitoring system and,
either that system meets the performance specifications and quality assurance
and quality control measures of 40 C.F.R. part 60, adopted and incorporated in
Rule 62-204.800, F.A.C., or that
system meets the performance specifications and quality assurance and quality
control measures of 40 C.F.R. part 75, adopted and incorporated in Rule
62-204.800, F.A.C.
b. An emissions test shall not be required
for visible emissions for which a rule, permit, or other order requires that
emissions be measured by a continuous opacity monitoring system, and that
system meets the performance specifications and quality assurance and quality
control measures of 40 C.F.R. part 60, adopted and incorporated in Rule
62-204.800, F.A.C., and the
manufacturer's recommended quality assurance and quality control
measures.
c. For the purpose of
renewal of an air operation permit, an emissions test shall not be required for
any emissions unit that, in the previous five-year period of permitted
operation, operated for 400 hours or less (including during startup and
shutdown) during each calendar year included in the five-year period of
permitted operation. The first time an emissions unit subsequently exceeds 400
hours of operation during a calendar year, emissions must be tested no later
than 60 days after 400 hours of operation is exceeded in that calendar year, or
by the end of that calendar year, whichever is later.
d. For the purpose of renewal of an air
operation permit, an emissions test shall not be required for any emissions
unit with emissions generated solely from the combustion of fuel provided that,
in the previous five-year period of permitted operation, the emissions unit did
not burn any liquid fuel or solid fuel or fuel blend for more than 400 hours
combined, other than during startup, during each calendar year included in the
five-year period of permitted operation. The first time an emissions unit
subsequently burns any liquid fuel or solid fuel or fuel blend for more than
400 hours combined during a calendar year, emissions must be tested no later
than 60 days after the emissions unit's combined burning of any liquid fuel or
solid fuel or fuel blend exceeds 400 hours in that calendar year, or by the end
of that calendar year, whichever is later.
e. An emissions test shall not be required
for each fuel-specific emissions limit prior to the renewal of an air operation
permit for an emissions unit provided that, in the previous five-year period of
permitted operation, the fuel or fuel blend subject to a fuel-specific limit
was not burned for more than 400 hours, other than during startup, during each
calendar year included in the five-year period of permitted operation. The
first time an emissions unit subsequently burns a fuel or fuel blend subject to
a fuel-specific emission limit for more than 400 hours, other than during
startup, during any calendar year, an emissions test for that fuel or fuel
blend must be completed no later than 60 days after the emissions unit's
burning of that fuel or fuel blend exceeds 400 hours in that calendar year, or
by the end of that calendar year, whichever is later.
f. An emissions unit shall not be required to
start up for the sole purpose of conducting an emissions test to meet the
frequency requirements of subsection
62-297.310(8),
F.A.C. In such a case, an emissions test shall be completed no later than 60
days after the emissions unit starts up.
g. An emissions unit permitted to burn
multiple fuels or fuel blends shall not be required to switch fuels for the
sole purpose of conducting the emissions test to meet the frequency
requirements of subsection
62-297.310(8),
F.A.C. In such a case, an emissions test shall be completed no later than 60
days after a switch is made to burn the fuel or fuel blend for which testing is
required.
h. An emissions test for
visible emissions shall not be required for emissions units exempted from air
permitting pursuant to paragraph
62-210.300(3)(a) or
(b), F.A.C.; emissions units determined to be
insignificant pursuant to paragraph
62-213.430(6)(b),
F.A.C.; or emissions units authorized pursuant to the general permit provisions
in subsection 62-210.300(4),
F.A.C., unless the general permit specifically requires such
testing.
(c)
Special Compliance Tests. When the Department, after investigation, has good
reason (such as complaints, increased visible emissions or questionable
maintenance of control equipment) to believe that any applicable emission
standard contained in a Department rule or in a permit issued pursuant to those
rules is being violated, it shall require the owner or operator of the
emissions unit to conduct compliance tests which identify the nature and
quantity of pollutant emissions from the emissions unit, unless the Department
obtains other information sufficient to demonstrate compliance. The owner or
operator of the emissions unit shall provide a report on the results of said
tests to the Department in accordance with the provisions of subsection
62-297.310(10),
F.A.C.
(9) Scheduling and
Notification. At least 15 days prior to the date on which each required
emissions test is to begin, the owner or operator shall notify the air
compliance program identified by permit, unless shorter notice is agreed to by
the appropriate air compliance program. The notification shall include the
date, time, place of each such test, Facility ID Number, Emission Unit ID
Number(s) and description(s), Emission Point Number(s) and description(s), test
method(s), pollutant(s) to be tested, along with the name and telephone number
of the person who will be responsible for conducting such test(s) for the owner
or operator. If a scheduled emissions test needs to be re-scheduled, the owner
or operator shall submit to the appropriate air compliance program a revised
notification at least seven days prior to the re-scheduled emissions test date
or arrange a re-scheduled test date with the appropriate air compliance program
by mutual agreement.
(10) Test
Reports.
(a) The owner or owner's authorized
agent of an emissions unit for which an emissions test is required shall submit
a written test report to the compliance authority specified by permit, on the
results of each such test as soon as practicable but no later than 45 days
after the last run of each test is completed. Test reports may be submitted
electronically.
(b) If the owner or
owner's authorized agent of an emissions unit for which an emissions test is
required submits the results of each such test electronically using the EPA
Electronic Reporting Tool (ERT), the written report specified in paragraph
62-297.310(10)(a),
F.A.C., need not be submitted, provided the conditions of subparagraphs
62-297.310(10)(b)
1. through 3., F.A.C., are met:
1. The owner
or owner's authorized agent shall submit the test information using the ERT as
soon as practicable but no later than 45 days after the last run of each test
is completed,
2. The test
information shall provide, as a minimum, the information specified in
subparagraphs 62-297.310(10)(c)
1. through 24., F.A.C.; and,
3. The
compliance authority specified by permit must receive written notification, no
later than 45 days after the last run of each test is completed, of the date
that the test data was submitted using the ERT.
(c) The test report shall provide sufficient
detail on the emissions unit tested and the test procedures used to allow the
Department to determine if the test was properly conducted and the test results
properly computed. As a minimum, the test report, other than for an EPA Method
9 test, shall provide the following information:
1. The type, location, and identification
number of the emissions unit tested.
2. The facility at which the emissions unit
is located.
3. The owner and, if
other than the owner, operator of the emissions unit.
4. The type and amount of fuels and materials
typically used and processed, and the actual types and amounts of fuels used
and material processed during each test run.
5. If necessary in order to compare the
emissions test results with an applicable emission limiting standard, the
means, raw data, and computations used to determine the amount of fuels used
and materials processed.
6. The
type of air pollution control devices installed on the emissions unit, their
general condition, their typical operating parameters, and their actual
operating parameters during each test run.
7. A diagram of the sampling location,
including the distance to any upstream and downstream bends or other flow
disturbances.
8. The date, starting
time, and duration of each sampling run.
9. The test procedures, including any
authorized alternative procedures, used.
10. The number of points sampled, and the
configuration and location of the sampling plane.
11. For each sampling point for each run, the
dry gas meter reading, velocity head, pressure drop across the stack or duct,
temperatures, average meter temperatures, and sample time per point.
12. The type, manufacturer, and configuration
of the sampling equipment used.
13.
Data related to the required calibration of the test equipment.
14. Data on the identification, processing,
and weights of all filters used.
15. Data on the types and amounts of any
chemical solutions used.
16. For
each sampling run, data on the amount of pollutant collected from each sampling
probe.
17. For each sampling run,
data on the amount of pollutant collected from the filters.
18. For each sampling run, data on the amount
of pollutant collected from the impingers.
19. The names of individuals who furnished
the process variable data, conducted the test, analyzed the samples and
prepared the report.
20. All
measured and calculated data required to be determined by each applicable test
procedure for each run.
21. The
detailed calculations for one run that relate the collected data to the
calculated emission rate or concentration, as applicable.
22. The applicable emission standard, and the
resulting maximum allowable emission rate or concentration for the emissions
unit, as applicable, plus the test result in the same form and unit of
measure.
23. When an emissions test
is conducted for the Department or its agent, the person who conducts the test
shall provide the certification with respect to the test procedures used. The
owner or owner's authorized agent shall certify that all data required and
provided to the person conducting the test are true and correct to his or her
knowledge.
24. For non-Title V
sources, a certification by the owner or owner's authorized agent that, to his
or her knowledge, all data submitted are true and correct.
25. Any report submitted for a Title V source
shall contain certification by a responsible official. This certification shall
state that, based on information and belief formed after reasonable inquiry,
the statements and information in the document are true, accurate, and
complete.
Notes
Rulemaking Authority 403.061 FS. Law Implemented 403.031, 403.061, 403.087, 403.0872 FS.
Formerly 17-2.700(1)(b), 17-297.310, Amended 11-23-94, 3-13-96, 10-28-97, 3-2-99, 3-9-15.
State regulations are updated quarterly; we currently have two versions available. Below is a comparison between our most recent version and the prior quarterly release. More comparison features will be added as we have more versions to compare.
(1) Applicability. Unless otherwise stated in a specific rule, permit, or other order, the general requirements set forth in subsections 62-297.310(2) through (10), F.A.C., shall be used for regulated stationary sources' emissions tests for comparison with air pollution emission-limiting standards that are enforceable under state law. An emissions test is an emissions rate test, a concentration test, or an opacity test.
(2) Required Number of Test Runs. For emission rate or concentration limitations, an emissions test shall consist of three valid test runs to determine the total air pollutant emission rate or concentration through the test section of the stack or duct. A valid test run is a test run that meets all requirements of the applicable test method. An emissions test shall also consist of three distinct determinations of any applicable process parameters corresponding to the three distinct test run time periods during which the emission rate or concentration was measured when such data are needed in conjunction with emissions data to compare the emissions test results with the applicable emission limiting standards. Such data shall be obtained pursuant to subsection 62-297.310(6), F.A.C. The three required test runs shall be completed within one consecutive five-day period. In the event that a sample is lost or one of the three runs must be discontinued because of circumstances beyond the control of the owner or operator, and a valid third run cannot be obtained within the five day period allowed for the test, results of the two valid runs shall be accepted, provided that the arithmetic mean of the results of the two valid runs is at least 20% below the allowable emission limiting standard.
(3) Operating Conditions during Emissions Testing. Testing of emissions shall be conducted with the emissions unit operating at the testing capacity as defined below. If it is impracticable to test at the testing capacity, an emissions unit may be tested at less than the testing capacity. If an emissions unit is tested at less than the testing capacity, another emissions test shall be conducted and completed no later than 60 days after the emissions unit operation exceeds 110% of the capacity at which its most recent emissions test was conducted.
(a) Combustion Turbines. (Reserved)
(b) All Other Sources. Testing capacity is defined as at least 90 percent of the maximum operation rate specified by the permit.
(4) Calculation of Emission Rate or Concentration. The emission rate or concentration used for comparison with the relevant standard shall be the arithmetic average of the emission rate or concentration determined by each of the three valid test runs unless otherwise specified in an applicable rule or test method. Data collected during periods of soot blowing shall not be excluded from any calculation of emission rate or concentration.
(5) Required Sampling Times and Observation Periods. Unless otherwise specified in an applicable test method, rule, permit, or other order, the owner or operator shall conduct emissions tests in accordance with the following procedures:
(a) Emission Rate or Concentration Tests. The required sampling time for each test run shall be no less than one hour and no greater than four hours, and the sampling time at each sampling point shall be of equal intervals of at least two minutes, except that for operations that are typically completed within less than the minimum required sampling time, the duration of each test run shall include each occurrence of the operation during the minimum required sampling time. The test period shall include the period of typical operation during which the highest representative emissions are expected to occur.
(b) Opacity Tests. When EPA Method 9 is specified as the applicable opacity test method, the required minimum period of observation for a visible emissions test shall be 60 minutes for emissions units that are subject to a multiple-valued opacity standard and 30 minutes for all other emissions units, except that for batch, cyclical processes, or other operations that are typically completed within less than the minimum observation period, the period of observation shall include each occurrence of the operation during the minimum observation period. The opacity test observation period shall include the period during which the highest opacity emissions can reasonably be expected to occur.
(6) Determination of Process Parameters.
(a) Required Process Equipment. The owner or operator of an emissions unit for which emissions tests are required shall install, operate, and maintain equipment or instruments necessary to determine process parameters, when such data are needed in conjunction with emissions data to compare emissions test results with applicable emission limiting standards.
(b) Accuracy of Process Measurement Equipment. Equipment or instruments used to directly or indirectly determine process parameters shall be calibrated and adjusted so as to determine the value of the process parameter to within 10 percent of its true value.
(7) Required Emissions Testing Facilities.
(a) The owner or operator of an emissions unit, for which an emissions test other than a visible emissions test is required, shall provide emissions testing facilities that meet the requirements of 40 CFR 60.8(e), adopted and incorporated in Rule 62-204.800, F.A.C.
(b) Permanent Emissions Testing Facilities. The owner or operator of an emissions unit, for which an emissions test other than a visible emissions test is required on at least an annual basis, shall install and maintain permanent emissions testing facilities.
(c) Temporary Emissions Testing Facilities. The owner or operator of an emissions unit that is not required to conduct an emissions test on at least an annual basis may use permanent or temporary emissions testing facilities. If the owner or operator chooses to use temporary emissions testing facilities on an emissions unit, and the Department elects to test the unit, such temporary facilities shall be installed on the emissions unit within 5 days of a request by the Department and remain on the emissions unit until the test is completed.
(8) Frequency of Emissions Tests. The following provisions apply only to those emissions units that are subject to an emissions-limiting standard for which emissions testing is required.
(a) Annual Emissions Tests Required.
1. Where used in Rules 62-210.310, 62-297.310, or Chapter 62-296, F.A.C., to refer to frequency of required emissions tests, the terms "annual, " "annually, " and "annually thereafter" shall mean no less frequently than once every calendar year (January 1 - December 31).
2. Unless exempted by subparagraph 62-297.310(8)(a) 5., F.A.C., the owner or operator shall have an emissions unit tested annually for each of the following pollutants that has an emissions-limiting standard for which emissions testing is required:
a. Each hazardous air pollutant regulated by 40 C.F.R. Part 61, adopted and incorporated by reference at Rule 62-204.800, F.A.C.; and,
b. Any other regulated air pollutant, as defined at Rule 62-210.200, F.A.C., or a pollutant designated as a surrogate to a regulated air pollutant by an applicable rule or order, if allowable emissions equal or exceed 100 tons per year.
3. Unless exempted by subparagraph 62-297.310(8)(a) 5., F.A.C., the owner or operator shall have an emissions unit tested annually for visible emissions, if there is an applicable standard other than the general opacity standard of subparagraph 62-296.320(4)(b) 1., F.A.C.
4. Unless exempted by subparagraph 62-297.310(8)(a) 5., F.A.C., the owner or operator shall have an emissions unit tested annually if a rule, permit or other order issued after March 9, 2015, requires an initial emissions test but is silent as to the frequency of additional testing. A rule, permit, or other order that states that no further testing is required after an initial test, or which expressly lists or describes the tests that shall be conducted annually, is not considered silent as to the frequency of additional testing. Annual testing is not required where a permit or other order issued prior to March 9, 2015, is silent as to the frequency of additional testing.
5. Exemptions from subparagraphs 62-297.310(8)(a) 2., 3., and 4., F.A.C.
a. An annual emissions test shall not be required for any pollutant for which a rule, permit, or other order requires emissions testing at some other specific frequency. If multiple applicable rules, permits, or other orders, other than subparagraphs 62-297.310(8)(a) 2., 3., and 4., F.A.C., require different testing frequencies, testing must comply with the frequency requirements of each such rule, permit, or order.
b. An annual emissions test shall not be required for any pollutant for which a rule, permit, or other order requires that the pollutant emissions be measured by a continuous emission monitoring system and, either that system meets the performance specifications and quality assurance and quality control measures of 40 CFR part 60, adopted and incorporated in Rule 62-204.800, F.A.C., or that system meets the performance specifications and quality assurance and quality control measures of 40 C.F.R. part 75, adopted and incorporated in Rule 62-204.800, F.A.C.
c. An annual emissions test shall not be required for visible emissions for which a rule, permit, or other order requires that emissions be measured by a continuous opacity monitoring system, and that system meets the performance specifications and quality assurance and quality control measures of 40 C.F.R. part 60, adopted and incorporated in Rule 62-204.800, F.A.C., and the manufacturer's recommended quality assurance and quality control measures.
d. An annual emissions test shall not be required for any emissions unit that operated for 400 hours or less (including during startup and shutdown) during the calendar year. If an emission unit operates for more than 400 hours during the calendar year, an emissions test shall be completed no later than 60 days after the emissions unit's annual operation exceeds 400 hours, or by the end of the calendar year, whichever is later.
e. An annual emissions test shall not be required for any emissions unit with emissions generated solely from the combustion of fuel, provided that the emissions unit does not burn any liquid fuel or solid fuel or fuel blend for more than 400 hours combined, other than during startup, during the calendar year. If an emissions unit's liquid fuel or solid fuel or fuel blend burning exceeds 400 hours combined during the calendar year, other than during startup, an emissions test shall be completed no later than 60 days after the emissions unit's liquid fuel or solid fuel or fuel blend burning exceeds 400 hours combined, or by the end of the calendar year, whichever is later.
f. An annual emissions test shall not be required for each fuel-specific emissions limit, provided the fuel or fuel blend subject to a fuel-specific limit was not burned for more than 400 hours, other than during startup, during the calendar year. If an emissions unit burns a fuel or fuel blend subject to a fuel-specific emission limit for more than 400 hours, other than during startup, during the calendar year, an emissions test for that fuel or fuel blend shall be completed no later than 60 days after the unit's burning of that fuel or fuel blend exceeds 400 hours, or by the end of the calendar year, whichever is later.
g. An emissions unit shall not be required to start up for the sole purpose of conducting an emissions test to meet the frequency requirements of subsection 62-297.310(8), F.A.C. In such a case, an emissions test shall be completed no later than 60 days after the emissions unit next starts up.
h. An emissions unit permitted to burn multiple fuels or fuel blends shall not be required to switch fuels for the sole purpose of conducting an annual emissions test to meet the frequency requirements of subsection 62-297.310(8), F.A.C. In such a case, an emissions test shall be completed no later than 60 days after a switch is made to burn the fuel or fuel blend for which testing is required.
i. An annual emissions test for visible emissions shall not be required for emissions units exempted from air permitting pursuant to paragraph 62-210.300(3)(a) or (b), F.A.C.; emissions units determined to be insignificant pursuant to paragraph 62-213.430(6)(b), F.A.C.; or emissions units authorized pursuant to the general permit provisions in subsection 62-210.300(4), F.A.C., unless the general permit specifically requires such testing.
(b) Emissions Tests Prior to Obtaining an Air Operation Permit.
1. Unless exempted by subparagraph 62-297.310(8)(b) 3., F.A.C., prior to obtaining an initial or renewal air operation permit for any emissions unit that is subject to any emission-limiting standard, the owner or operator shall have an emissions test conducted for each such standard to assist in providing reasonable assurance, per Rule 62-4.070, F.A.C., that the emission-limiting standard can be met and shall submit the test report as specified in subsection 62-297.310(10), F.A.C. For an emissions unit at a Title V source, such prior emissions testing is not required provided that an emissions testing compliance plan is included in the Title V permit.
2. For the purpose of renewal of an air operation permit, the owner or operator may satisfy the requirements of subparagraph 62-297.310(8)(b) 1., F.A.C., for any emissions unit by submitting the most recent emissions test, as specified in subsection 62-297.310(10), F.A.C., provided such test occurred within the term of the current operating permit.
3. Exemptions from subparagraph 62-297.310(8)(b) 1., F.A.C.
a. An emissions test shall not be required for any pollutant for which a rule, permit, or other order requires that the emissions be measured by a continuous emission monitoring system and, either that system meets the performance specifications and quality assurance and quality control measures of 40 C.F.R. part 60, adopted and incorporated in Rule 62-204.800, F.A.C., or that system meets the performance specifications and quality assurance and quality control measures of 40 C.F.R. part 75, adopted and incorporated in Rule 62-204.800, F.A.C.
b. An emissions test shall not be required for visible emissions for which a rule, permit, or other order requires that emissions be measured by a continuous opacity monitoring system, and that system meets the performance specifications and quality assurance and quality control measures of 40 C.F.R. part 60, adopted and incorporated in Rule 62-204.800, F.A.C., and the manufacturer's recommended quality assurance and quality control measures.
c. For the purpose of renewal of an air operation permit, an emissions test shall not be required for any emissions unit that, in the previous five-year period of permitted operation, operated for 400 hours or less (including during startup and shutdown) during each calendar year included in the five-year period of permitted operation. The first time an emissions unit subsequently exceeds 400 hours of operation during a calendar year, emissions must be tested no later than 60 days after 400 hours of operation is exceeded in that calendar year, or by the end of that calendar year, whichever is later.
d. For the purpose of renewal of an air operation permit, an emissions test shall not be required for any emissions unit with emissions generated solely from the combustion of fuel provided that, in the previous five-year period of permitted operation, the emissions unit did not burn any liquid fuel or solid fuel or fuel blend for more than 400 hours combined, other than during startup, during each calendar year included in the five-year period of permitted operation. The first time an emissions unit subsequently burns any liquid fuel or solid fuel or fuel blend for more than 400 hours combined during a calendar year, emissions must be tested no later than 60 days after the emissions unit's combined burning of any liquid fuel or solid fuel or fuel blend exceeds 400 hours in that calendar year, or by the end of that calendar year, whichever is later.
e. An emissions test shall not be required for each fuel-specific emissions limit prior to the renewal of an air operation permit for an emissions unit provided that, in the previous five-year period of permitted operation, the fuel or fuel blend subject to a fuel-specific limit was not burned for more than 400 hours, other than during startup, during each calendar year included in the five-year period of permitted operation. The first time an emissions unit subsequently burns a fuel or fuel blend subject to a fuel-specific emission limit for more than 400 hours, other than during startup, during any calendar year, an emissions test for that fuel or fuel blend must be completed no later than 60 days after the emissions unit's burning of that fuel or fuel blend exceeds 400 hours in that calendar year, or by the end of that calendar year, whichever is later.
f. An emissions unit shall not be required to start up for the sole purpose of conducting an emissions test to meet the frequency requirements of subsection 62-297.310(8), F.A.C. In such a case, an emissions test shall be completed no later than 60 days after the emissions unit starts up.
g. An emissions unit permitted to burn multiple fuels or fuel blends shall not be required to switch fuels for the sole purpose of conducting the emissions test to meet the frequency requirements of subsection 62-297.310(8), F.A.C. In such a case, an emissions test shall be completed no later than 60 days after a switch is made to burn the fuel or fuel blend for which testing is required.
h. An emissions test for visible emissions shall not be required for emissions units exempted from air permitting pursuant to paragraph 62-210.300(3)(a) or (b), F.A.C.; emissions units determined to be insignificant pursuant to paragraph 62-213.430(6)(b), F.A.C.; or emissions units authorized pursuant to the general permit provisions in subsection 62-210.300(4), F.A.C., unless the general permit specifically requires such testing.
(c) Special Compliance Tests. When the Department, after investigation, has good reason (such as complaints, increased visible emissions or questionable maintenance of control equipment) to believe that any applicable emission standard contained in a Department rule or in a permit issued pursuant to those rules is being violated, it shall require the owner or operator of the emissions unit to conduct compliance tests which identify the nature and quantity of pollutant emissions from the emissions unit, unless the Department obtains other information sufficient to demonstrate compliance. The owner or operator of the emissions unit shall provide a report on the results of said tests to the Department in accordance with the provisions of subsection 62-297.310(10), F.A.C.
(9) Scheduling and Notification. At least 15 days prior to the date on which each required emissions test is to begin, the owner or operator shall notify the air compliance program identified by permit, unless shorter notice is agreed to by the appropriate air compliance program. The notification shall include the date, time, place of each such test, Facility ID Number, Emission Unit ID Number(s) and description(s), Emission Point Number(s) and description(s), test method(s), pollutant(s) to be tested, along with the name and telephone number of the person who will be responsible for conducting such test(s) for the owner or operator. If a scheduled emissions test needs to be re-scheduled, the owner or operator shall submit to the appropriate air compliance program a revised notification at least seven days prior to the re-scheduled emissions test date or arrange a re-scheduled test date with the appropriate air compliance program by mutual agreement.
(10) Test Reports.
(a) The owner or owner's authorized agent of an emissions unit for which an emissions test is required shall submit a written test report to the compliance authority specified by permit, on the results of each such test as soon as practicable but no later than 45 days after the last run of each test is completed. Test reports may be submitted electronically.
(b) If the owner or owner's authorized agent of an emissions unit for which an emissions test is required submits the results of each such test electronically using the EPA Electronic Reporting Tool (ERT), the written report specified in paragraph 62-297.310(10)(a), F.A.C., need not be submitted, provided the conditions of subparagraphs 62-297.310(10)(b) 1. through 3., F.A.C., are met:
1. The owner or owner's authorized agent shall submit the test information using the ERT as soon as practicable but no later than 45 days after the last run of each test is completed,
2. The test information shall provide, as a minimum, the information specified in subparagraphs 62-297.310(10)(c) 1. through 24., F.A.C.; and,
3. The compliance authority specified by permit must receive written notification, no later than 45 days after the last run of each test is completed, of the date that the test data was submitted using the ERT.
(c) The test report shall provide sufficient detail on the emissions unit tested and the test procedures used to allow the Department to determine if the test was properly conducted and the test results properly computed. As a minimum, the test report, other than for an EPA Method 9 test, shall provide the following information:
1. The type, location, and identification number of the emissions unit tested.
2. The facility at which the emissions unit is located.
3. The owner and, if other than the owner, operator of the emissions unit.
4. The type and amount of fuels and materials typically used and processed, and the actual types and amounts of fuels used and material processed during each test run.
5. If necessary in order to compare the emissions test results with an applicable emission limiting standard, the means, raw data, and computations used to determine the amount of fuels used and materials processed.
6. The type of air pollution control devices installed on the emissions unit, their general condition, their typical operating parameters, and their actual operating parameters during each test run.
7. A diagram of the sampling location, including the distance to any upstream and downstream bends or other flow disturbances.
8. The date, starting time, and duration of each sampling run.
9. The test procedures, including any authorized alternative procedures, used.
10. The number of points sampled, and the configuration and location of the sampling plane.
11. For each sampling point for each run, the dry gas meter reading, velocity head, pressure drop across the stack or duct, temperatures, average meter temperatures, and sample time per point.
12. The type, manufacturer, and configuration of the sampling equipment used.
13. Data related to the required calibration of the test equipment.
14. Data on the identification, processing, and weights of all filters used.
15. Data on the types and amounts of any chemical solutions used.
16. For each sampling run, data on the amount of pollutant collected from each sampling probe.
17. For each sampling run, data on the amount of pollutant collected from the filters.
18. For each sampling run, data on the amount of pollutant collected from the impingers.
19. The names of individuals who furnished the process variable data, conducted the test, analyzed the samples and prepared the report.
20. All measured and calculated data required to be determined by each applicable test procedure for each run.
21. The detailed calculations for one run that relate the collected data to the calculated emission rate or concentration, as applicable.
22. The applicable emission standard, and the resulting maximum allowable emission rate or concentration for the emissions unit, as applicable, plus the test result in the same form and unit of measure.
23. When an emissions test is conducted for the Department or its agent, the person who conducts the test shall provide the certification with respect to the test procedures used. The owner or owner's authorized agent shall certify that all data required and provided to the person conducting the test are true and correct to his or her knowledge.
24. For non-Title V sources, a certification by the owner or owner's authorized agent that, to his or her knowledge, all data submitted are true and correct.
25. Any report submitted for a Title V source shall contain certification by a responsible official. This certification shall state that, based on information and belief formed after reasonable inquiry, the statements and information in the document are true, accurate, and complete.
Notes
Rulemaking Authority 403.061 FS. Law Implemented 403.031, 403.061, 403.087, 403.0872 FS.
Formerly 17-2.700(1)(b), 17-297.310, Amended 11-23-94, 3-13-96, 10-28-97, 3-2-99, 3-9-15.